» October 2016

252627282930 1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30 31 12345


» Log in

User Name:


Not a member yet?
Register Now!

» Today's Birthdays



Results 1 to 4 of 4
  1. #1
    Join Date
    May 2011
    Santa Rosa
    Post Thanks / Like

    Need some help with ce 3000-60 MK2

    Hello all and thanks for having this site
    I have a Graphtec CE3000-60 MK2 and it has worked perfect for years using ILL 10 with out any problems
    Recently I had to change operating systems, I went from window's XP PRO to Window's 7 business 32 bit
    I down loaded the controller and drivers and they installed correctly I think? I did have a hitch with the controller the first time but it finally installed, but it will not work, the computer see' the Graphtec 3000 but it will not do anything.
    I have un plugged the plotter and re booted the computer but still nothing
    The only thing that has changed is that I went to window's 7 all and everything else is the same, could someone here lead me in the correct direction on how to find out what is wrong

  2. #2
    Join Date
    Oct 2005
    Post Thanks / Like
    Did you download the drivers for Windows 7? Look here plotters>legacy CE3000-MK2 > drivers

  3. #3
    Join Date
    May 2011
    Santa Rosa
    Post Thanks / Like
    I did go there and download both the controller and drivers,
    what I did is un install them and re install them again and I got an error code this time saying that the controller

    The specified plotter model is not supported. The Graphtec Cutting Plotter Controller can only be launched for supported plotter models.
    Or, if the connect plotter is Craft ROBO-Pro, the Controller can only be launched if the firmware versio is Ver. 7.00 or later.
    The firmware version number is displayed for serveral seconds on the plotter's LCD when the power is first turned on. [code=1009]

    So I decided to turn off the plotter and check the LCD screen to see what version I have and this is what it said
    V 5.20 GL
    So I still have no idea what to do next

  4. #4
    Join Date
    May 2011
    Santa Rosa
    Post Thanks / Like
    I took the time to call tech support this morning, and I got to say I got right though with out a hitch, the guy walked me though what I needed to get done and it works
    you have to down load the driver, and the CM2 in order to make it work, the one thing I didnt down load was the CM2 before
    the cutter works great, there is again a learning curve on this as its a new program but I'll get it figured out some how

Similar Threads

  1. Ce 3000-60 or Qe-60
    By thmooch in forum Graphtec
    Replies: 1
    Last Post: 12-05-2007, 09:03 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts


» Search for Fonts at Signs 101

Looking for fonts? We highly recommend MyFonts.com



Powered by vBadvanced CMPS v4.3.0


All posts and other information available at Signs 101 should be viewed as the opinion only of the poster. No claim is made that any information is accurate. As such, each reader should not rely on any information available here as accurate and should independently verify such accuracy. In addition, no claim is made that posts made here will be free from profanity, obscenity, rude, hurtful, libelous or insulting opinions of the poster. Such posts should, however, be reported to an Administrator for review.

Neither the owners, employees, officers nor directors of Signs 101 shall be held responsible or liable under any legal theory for any loss or injury resulting from any post, information made available, policy, action or lack of an action at Signs 101. Your use of this website is your acceptance of these terms and conditions of use.