Search results

  1. HIGHSPEEDGRAPHIX

    Race Numbers

    Purchase from School of racing graphics, the owner is great to work with and their files and work are amazing! the font is like $25 bucks tops
  2. HIGHSPEEDGRAPHIX

    2000 Club Car Wrap

    anyone know how much material is needed to color change wrap a 2000 club car. I can do an 2000 EZGo TXT on 10' (60" roll). It looks to be the same or less. Wondering if i can get away with ordering 4 yards over 5. Thanks, Roger
  3. HIGHSPEEDGRAPHIX

    VJ1324 Mutoh Carriage Noise when moving/printing Left and Right

    Thanks buddy! i greased the tracking up GAC stated too and used fishing reel oil on the tension bearings, between the two it seemed to take care of the noise, it wasnt bad to the point i was like OMG my printer is gonna blow out or something but i do "hear" things all the time, lol
  4. HIGHSPEEDGRAPHIX

    VJ1324 Mutoh Carriage Noise when moving/printing Left and Right

    Thanks FatCat, im going to try a little grease in the sealed bearings, i have noticed (what little i have run it) that when i override and run carriage at low speed its not a bad, The noise does run the whole width, but i have had a few moments where the noise dissipates then comes back. The...
  5. HIGHSPEEDGRAPHIX

    VJ1324 Mutoh Carriage Noise when moving/printing Left and Right

    Thanks, im going to give that a try first. Another thing i noticed is that when loading media or using Media Cut the Head travles slower so that seems like why i dont hear the noise. The Noise did start abruptly....8 inchs into the print it was "normal sounding" and the next pass it had this...
  6. HIGHSPEEDGRAPHIX

    VJ1324 Mutoh Carriage Noise when moving/printing Left and Right

    By clean i mean no ink, gunk or dust its slightly greased but it prob could use a little more, any recommendations on grease i can pick at a hardware store?
  7. HIGHSPEEDGRAPHIX

    VJ1324 Mutoh Carriage Noise when moving/printing Left and Right

    Hello folks, I have a carriage noise when my Mutoh VJ1324 is printing. It started about 8 inchs into a print. The print Quality has not been lost. I suspect it may be a bearing... but when i do a media cut or load media it do not hear it....But when go to CR maintenance i do hear it as it goes...
  8. HIGHSPEEDGRAPHIX

    Profile Help Flexi 12 on Mutoh 1324- Avery 2923

    Profile Help Flexi 12 on Mutoh 1324 - Avery 2923 Need help trying to get Flexi to print on Matte Avery 2923 ez.....Flexi only comes with Avey 1005, and i went to Avery but the file the give me is a Ptf? anyone know how to use this file or have something in a ICC already? Thanks
  9. HIGHSPEEDGRAPHIX

    RIP Files to a SSD drive or mechanical type?

    I not worried about durability since it would be dedicated to RIP files and their temp and archived files that go along with it. Anyone with experience comparing? any noticeable difference?
  10. HIGHSPEEDGRAPHIX

    RIP Files to a SSD drive or mechanical type?

    Is there any speed advantage to Ripping to a SSD. I use Flex 12 and sometimes Sign Lab 9. I have an extra 128 GB SSD drive sitting around thinking about just dedicating it to ripping. Thanks, Roger
  11. HIGHSPEEDGRAPHIX

    Flexi 12 Cutting at 1/4 size?

    Hi, I have just upgraded from Flexi 7 and Signlab 9 to Flexi 12.....I have my Graphtec 7000-130 set to GPGL and communicating but i have to manually change the "scale" to "4" in the plotter menu settings every-time... I see there is an output size compensation but not able to figure out how to...
  12. HIGHSPEEDGRAPHIX

    Mutoh VJ 1204 Banding Issues

    are you running the correct profile. It could be media feed too, but your profile also controls the feed of the media and can cause banding. Have you tried another media type?
  13. HIGHSPEEDGRAPHIX

    RED at day ORANGE at night.

    call me old school but i would cut that in translucent vinyl as well.
  14. HIGHSPEEDGRAPHIX

    How do you cut using a cutter with VJ 1204?

    you cant cut with a VJ1204 or any of the Value Jets, You need a stand alone plotter, like a graptech....needs to have opitcal eye 7000 series or newer i beleive. You also need software that supports print and cut. you can use the Cut Master 2 plug in for illustrator to set up files....repeats...
  15. HIGHSPEEDGRAPHIX

    Problems with gradient in signlab

    I think you'll need to convert the fade to raster before saving it out to print, then you wont have that issue.
  16. HIGHSPEEDGRAPHIX

    Best transfer method for Frosted Crystal on glass

    the liner sucks to peel, off...be very careful... I used Conform R hi-tack. That frosted crystal hates pre-mask...... If you cut too deep this also doesn't help. For install, I use wet application method. I pre-mask only the knockout. scrap clean the window, soak the window, peel the film up...
  17. HIGHSPEEDGRAPHIX

    font match script

    awsome thanks Rex!
  18. HIGHSPEEDGRAPHIX

    font match script

    a file might help!
  19. HIGHSPEEDGRAPHIX

    font match script

    need an exact match,, anyone recognize this one? Thanks
  20. HIGHSPEEDGRAPHIX

    Rooster Crow Font Match

    anyone got a match on this one? Thanks!
Top