Search results

I am finally getting ready to hire help and had a question on the adobe license. I have been using personal and had it on my iMac and MacBook so the files would transfer between the two. Now that I need to add another computer and either needed to figure out the best way to do that so that I can...

We have an S2 T series that we have been using for years with mainly no problems for the smaller cut jobs. For some reason I have a problem with jobs over 8' and it is hit or miss with being accurate. I did two 8' prints today and it cut perfect and then on the third it was off as soon as it...

I have a latex 335 that we just got up and going again after being down for a month or so. It was printing about 60' of banner material perfect and I just went to print some vinyl and it started out good and then the green started printing into a yellowish color. I did a printhead clean and did...

This is probably the easiest thing to do and I have no idea why I am not getting it to work. I have been using flexi for years but apparently was printing and cutting the hard way. I just started importing directly to the production manager to print and contour cut from illustrator. My problem...

Does anyone have any experience with the FCX2000? We would mainly be using it to cut motocross graphics that are 21 mil. The vinyl we print on is 30" Wide so the 36" size would work perfect. I just wasn't sure if it was a decent cutter or if you are just better off going with something larger or...

I have an S2 that we use for all of our cutting and cut out of flexi. I all the sudden am having a problem when it reads the opos marks it will read from the front to the back perfect and then when it moves to the left side to read the back to front it seems to overshoot the back mark and takes...

I do a good amount of vehicles and some basic aluminum signs but typically we just do 4' X 8' sheets and the customers are just putting them in their own frame they already have. I have a job to install 2 4' X 8' signs up on an existing frame about 15' off the ground and remove an old 180" X 8'...

I just did an install on some windows using Sihl value line 3215 80/20 perf and when you look at it from certain angles you can see marks in different areas. This is my first time using this material but is that common with this material or is there something I should have done differently on...

I have a latex 335 that we have been using for years with no problems and now for some reason all of a sudden on this briteline vinyl we have been using for years with the same profile as always our prints are coming out as shown in the attached image. I did a test print and it seems to be...

does anyone happen to know this font? I know I have seen it before but can't remember what it was.

Does anyone happen to know what font this is?

Does anyone happen to know what font this is?

Does anyone happen to know what font this is?

Does anyone know of any good profiles for the S80600 to use with Flexi? When we had our printer installed the tech just went with a basic 3m profile and I haven't found too much other than onyx profiles and wanted to try something different with our substance media. I know we can get better...

Is anyone familiar with the font used in this picture?

Does anyone happen to know the font that is used here?

Does anyone know what would cause this? When printing it sounds like the motor is making a different noise and the foil just seems to stick along the vinyl and not roll up into the other roll and just causes it to break after a few inches of printing.

I just paid epson to put two new heads in our S80600 and now for some reason on only the light grey we are getting these spots. The tech guy is working on it but they definitely aren't rushing to fix the problem. All of our settings are the same from before we had the heads replaced and the...

I am trying to do an ink flush on our S80600 but for some reason when I install the cleaning cartridges the printer is not accepting them and saying I need to place the correct color cartridges so I am not able to get out of that screen. Does anyone know how to fix that or why it won't accept them.

We have had our S80600 for a little over a year now and when we got the printer installed the computer we had for the rip wouldn't work with the version of onyx so the guy just set us up on our flexi subscription to use. I have heard that onyx is a whole lot better than flexi and I have heard...