Search results

Does anyone have excessive buckling and headstrikes on the L360? This is typically happening on lower end material (calendered) offerings from both oracal and avery. I assume heat is a factor but I don't have the same issue on our L26500. The material will sometimes buckle completely and get...

I am going crazy over this issue. For example, I print 2" wide by 1" tall decals on 54" material and contour cut them. The decals on the outer edge of the material cut fine but the inner ones or offset along the y axis. It is a gradual transition along the x axis from good to offset back to...

Has anyone had any decent results printing on convex with an HP latex? Convex does not support it but I am interested if anyone has tried it. Thanks...

Hey guys... I have searched all the threads I could and can't seem to find a similar issue to the one I am experiencing. 3 year old Mimaki JV33-160 (lightly used) I started printing a large area of cyan (4ft x 40ft section) and noticed slight banding. I stopped it and ran a test draw and a...

I have a customer that has a large extended range plastic gas tank for his KTM motorcycle and I am have a hard time finding any material that will hold up on the tank. Within a week or two it is full of bubbles and when you peal them off they are soaked in gas. I have used the array of convex...

We have had a huge influx of requests for the pink boulevard to be used in events. We wrapped it about a month ago to promote the Susan G. Komen Foundation. Here are some pics from this weekends Race for the Cure walk/run in Fort Worth over the weekend. It was used as the pace vehicle.

Here is my M109 finally finished at 4am this morning. It is not perfect, I ran out of time as I have to get it to the show today.. All for a good cause though... Team Pink Boulevard for the Dallas 3-day walk in November (Susan G. Komen).

My wife and I decided to participate in the Susan G. Komen 3-day walk for the cure (Breast Cancer) in Dallas in November. It has affected quite a few people close to home recently. We have to each raise $2300 in order to participate so while discussing how to raise the funds for the foundation...

This was installed for the all star weekend here in Dallas...

I have a feeling we are all going to be wrapping a few of these. We just finished this one and a lot of people were very interested in the little van.

I ordered a new Jv33-160 and was told it would take a week to be delivered. They finally showed up at my dock and 2 guys unloaded it. The tech was going to arrive the following day to install it. He called that afternoon and said he would come over and just take it out of the box and put it...

I have been in the market for another printer and have been eyeing the xj740. I just found out that roland has an instant rebate for August of $3500 for the 740 and $3000 for 640.

Hi Folks, Any ideas on this font. I just can't quite find a match. Thx.

Does anyone know how to print spot colors on an Edge from Flexi 7.6. Is there a specific color table required. There does not seem to be any specification in production manger and the flexi knowledge base has nothing. Thx..

Can Flexi Pro 7.6v2 be used to output to an edge LE? If so I presume contour cutting can be done with a Graphtec FC optically. Thx...

Anyone have the same problem we have where the vinyl rolls fall off the back of the machine when it is running. It typically happens when the roll has less than a third of the material left on it and is light. Don't have this problem on our Summas. Thx Dave

Anyone know this font "Val's"? This is the best pic I have which doesn't lend itself well to tracing.

Does anyone know if there is a thermal transfer material (gerber edge printable) that can be applied to sunbrella? Thx... Dave

I have been trolling this site for a little while but have not formally introduced myself. I am located about 45 miles east of Dallas (seems Texas and Florida are competing for dominant representation here). I had a vinyl business in Chicago 10 years ago. I took a 7 year break working for a...