I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
The word on the street was the new firmware SAO11B 1.16,9000 Firmware was supposed to silence the loud cooling fan, but is hasn't. Any one have this fan issue that the firmware has silenced it?
I think I see where it may have come from. Can I just order another and put it back in myself. Should I not use this printer until I replace it? Just curious what the purpose is?
Have a post below about my Seal 62 Base being out of commission due to a bad safety sensor which locks out the laminator from working (It does work in snail mode)
Have a call in to Grimco and awaiting there return call. Would prefer to pay someone on the side that is in se Pa. and could work on...
The only way to get the normal light to come on is to engage the snail mode with the foot pedal and normal light comes on but it is in the snail mode. If you turn snail off and press the normal mode the light does not come on even when pressing the foot pedal. Opened both ends and evrerything...
Our business is mainly printing on canvas and we have that really nailed down. What we are still looking for are several premium solvent papers for artist reproductions.
We have the Sunset Velvet Rag from Lexjet but when you print on it and compare it to a print off our pigment P8000 on Canson...
Just purchased a copy of Onyx Thrive 19 (All I could afford) for my used Epson s80600.
Doing some print and cut and my new Graphtec ce-7000 is not on the cutter list. It still works choosing the generic Graphtec but I had a heck of a time getting it to work. I was told Onyx had several patches...
The US Cutter folks could not figure it out and asked me to call Graphtec tomorrow. Was also told by Cutter that Graphic does not support Onyx..
I can move the offset + or - 0.118 or about 1/8" I went in and changed the offset movement to a max of 0.245 but even after entering it is not sticky...
Pretty sure it is user error but I need some help digging it out. The ce-7000 is not listed in Graphtec setup. Since there is no generic "Graphtec cutter' to select i have selected Fc-7000.
I cannot send anything to the cutter, registration mark or barcode to read. Nothing happens which means...
A little background first. I have a 3500 sq. ft. printing, photo mounting and framing studio near Morgantown, Pa. since 2009.
We primarily do hospitality fine art printing on canvas with 7 Epson printers. 2 are Dye sublimation. 3 heat presses, 2 Seal laminators and a shop full of framing...
I have 3 or 4 images I have tried to print with my s80600 and it is printing full width and then only about an inch or two of the image.
The printer then starts weeding blank paper down to the floor. Seems like something may be corrupted but I cannot figure it out.
Any ideas?
Just had a short conversation with my Epson tech. about turning my Epson off when it is not being used. I still have virtually no work for this thing. Maybe several jobs for an hour or two a week. I have it off all the time but turn it on every morning just to do a nozzle check. After my last...
Have been getting an intermittent 200a error code. Manual says to replace the mainboard and update the firmware. i updated the firmware but am still getting the occasional red light and error code. everything can look normal on the panel but all the buttons are dead, you cannot select anything...
I have an old copy of Onyx GamaPrint 12.2 Pro I am trying to learn before I spend more money on an upgrade.
Several issues I have been having. When I go to set up a new quickset there are no cutters shown. Only selection is none. I have set up my Graphtec ce-7000-60 as a generic cutter. I...
I am guessing I know the answer to this already but it does not hurt to ask. I purchased a used s80600 and it came with Onyx Gamma Print 12.2 which I finally got to work after 5 months. The list of cutters does not include the ce-7000. It does however show the ce-6000. Will this work or am I...
In the add cutters it only has the Graphtec 6000 as an option closest to my model. Will my 7000 work when choosing the 6000 cutter? If not is their a way to add my ce-7000 to the list?
I purchased a used s80600 and it did not come with any software. Had to replace both heads the first week which was a hard hit to take. I am printing using the Epson Edge Rip but it is weak at best. Is there anyone out there that might have an unused copy of Onyx from an extra printer you might...
Have been working on getting a good b&w on Chromaluxe metals for the last 5 years if not longer. Two printers and neither will give me a neutral b&w. An 8 color converted from new Epson P8000 with Ink Owl Ultra ink.
With this printer I made my own profiles with an i1 Pro. The second printer is...
I purchased a used s80600 and the Onyx rip did not come with it. I print primarily canvas and have not found anyone that has the .emx icc profiles. Printing using Epson Edge Rip and it does not read the Onyx profiles.
Breathing Color Urth Satin
Fredrix Satin SUV
Anyone have profiles for either...
Starting to get a little upset here. I paid for a premium membership and in over 3 weeks no one has responded to my emails. Since no one activated my member to member classified I put my for sale item here on the Epson page. Is anyone available to activate new member accounts?
Thank You
Dan Berg...
Paid for premium membership 3 weeks ago and despite repeated emails no one has activated my member to member classifieds so here I am.
For Sale Price Reduced
Bn-20a less then 3 months old. Just doesn’t fit in our print studio plan now that we have a 64” solvent. Ran 3 small jobs, that’s it...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.