• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. F

    none

    none

  3. Service Manual for Mimaki's

    write me your email ion pvt, i will send it to you

  4. Losing half the magenta color on left side

    if the cap is new, you have to try to replace the entire cap station: cap slider + cap slider base before to do this try to power off the printer, to dirt the capping with black ink and power on it again, then move the carriage on the left side of the printer and watch on the printhead plate...

  5. Motor problem blowing main board on Mimaki JV3-160SP

    Try to clean the carriage guide and lubricate it. Try to change the bushings (M400249) Check if the y chain and the pulley are ok Check the motor cables if they are ok Replace y motor again :noway:

  6. help please jv33 wont boot

    can you tell us the error code, or the message on your display?

  7. no black ink

    to change the pump is pretty easy: the pump is located right back your left media holder, you have to take off the panel behind the left media holder and you will see the two pumps, the pump is connected to the cap tops with the tygon tube, remember the position of the tubes to let you put the...

  8. Help

    Yes you have to change the pump

  9. Mimaki CJV30 Firmeware needed!!!

    i have some earlier firmware for cjv30. Write me your email address i will send to you

  10. no black ink

    what do you mean when you say "i did the cleaning"? Do you mean the nozzle wash cleaning? If it is the "nozzle wash" and the liquid fall down on the capping, maybe your pump is broken, you have to change it

  11. identify DX5 head model on Chinese printer

    thank you, but your link doesn't show anything

  12. no black ink

    Hi, try this in sequence: - watch the dampers, they have to be full - if the dampers are not full of black ink, take a siringe (without the needle) and try to pull the ink from the damper to fill it. - if the siringe method is not working and only air is on it it means that some o-ring is not...

  13. identify DX5 head model on Chinese printer

    Thank you for your answer, one last thing: on your JV33 are you using a "new" F186000 DX5 with decoder board? Thanx again

  14. identify DX5 head model on Chinese printer

    Hello Sightline! seems you have a lot of experience in this, so i'd like to ask you one thing: i have a Jv33 with SS21 inks which printhead DX5 have i to buy the F186000 is the right one? are there more than one kind of F18600 DX5 or is only one kind? i buy it from here...

  15. Mimaki JV3-160SP Print Head Replacement - Help Needed!

    I'm sorry Mike your yellow printhead is probably damaged, if it isn't, you have some problem with the flat cable, check if it is righly connected to the printhead and if it have some ink drops on the contacts. For my esperience your printhead could be damaged (90% of the cases like yours)

  16. New DX5 printheads cause a line at 60cm

    Hello! i bought a decoder board for DX5 printheads, can anyone tell me which is the P/N of the Epson DX5 that works on a Mimaki JV33? I specify that i need the solvent one. Thank you very much!

  17. Mimaki JV33/CJV30 Epson Printhead dx5

    Someone who can answer this simple question? thank you!

  18. Mimaki JV33/CJV30 Epson Printhead dx5

    Hello! i bought a decoder board for DX5 printheads, can anyone tell me which is the P/N of the Epson DX5 that works on a Mimaki JV33? I specify that i need the solvent one. Thank you very much!
Top