• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. concerned about solid black banners needing to gas out before mounting in banner stand Epson s80600L

    Why do you need banner to outta before putting in a retractable display? I use 10mil anti curl film in lieu of banner material. The s80 should be dry and ready to handle 3min after print finished. If blacks are wet you are laying down way too much ink 100/20/20/20 is all you need
  2. Epson s80600 random ink drops

    Did they replace the dampers as well? If they used the original it could be an issue. Aldo just make surge guards are clean.
  3. What RIPs support the onboard spectro of the HP700W.

    Onyx will allow connection to the 300 series printers I’m sure it will on 700-800 however you can only use it to linearize profiles and make basic profiles. Limited swatches.
  4. What to check for when buying used equipment?

    go on any printer on their network open up a web browser and type in the printer's ip address
  5. What to check for when buying used equipment?

    sorry for delay....the rails will absolutely devolve a bow from the carriage if the bushings wear out and printer is continuously run. This will leave the printer useless.
  6. What to check for when buying used equipment?

    Run a usage report. Run finger across carriage rail. If a rail is not oiled properly it will develop a grove. The rail in an hp cannot be replaced
  7. Epson 80600 2-Pass Profle

    you may need to use another profile that has 2 pass as an option. They may not have allowed for 2 pass because the quality would be unacceptable.
  8. Error E-HB-91, cannot print on multiple sheets on the HP 750

    are you set up to print only? set your printer to store. Send your files, then load media, then go to queue and release
  9. HP Latex Printing Reflective - Too hot

    Every profile you download or receive from a manufacturer or even another printer needs to be configured to your environment. HP creates their profiles in a lab with perfect conditions probably in Barcelona or Alpharetta. Two different parts of the world, probably same controlled variables in...
  10. Small shop using Latex 365 looking to upgrade, tell me what I should buy!

    You have had a printer for 6 years, required 1 service and now you need to replace a few Pips at $175ea? Id say you have gotten your money's worth. Have you had a PM service performed on the printer? You probably have some wear and tear parts needing some love. You can spend $2k and put the...
  11. Latex vs Solvent coverage per ml

    if you are going through that much cyan, you should nix both of these platforms and look at the Colorado...$.08/sq'
  12. Trouble with Acerbis grey Epson s80600

    There is a pdf Pantone file you can print from the onyx samples folder that loads on your computer. Does your profile match the media you are printing on? you need to start there or purchase an eye1. If you follow any of the suggestions above you will get where you are going. Noone will have a...
  13. Recommend a printer for big solid colors

    colorado M series if you have the budget or Epson s40, 60 80
  14. Colex polished edge acrylic?

    There should be a profile that downloads to leave a polished edge. It really just does a second pass to clean it up. Keep in mind, if you use your router bit for anything other than acrylic it will not give your the best edge. The router should be warmed up first as well. And if you specifically...
  15. Flat Bed Cutter Recommendations

    I can see that being an issue on the smaller table. I almost ordered that one...
  16. AUTOMATION and WORKFLOW

    I believe they had a promo at the last show that is still running.
  17. Material for custom packaging

    I run 18 and 24 point all day long from Lindenmeyer Available in 4x8 sheets
  18. Possible to apply Braille and tactile lettering directly to the wall?

    Bad idea and if an inspection is required, it will fail.
  19. Flat Bed Cutter Recommendations

    Aren’t your segments controlled by your table size? I’m not sure where I would ever need to control a segment. I have a 5x10 Colex with conveyer, we throw a full roll of graphics printed through onyx and it cuts beginning to end with zero interaction. I am using a Summa basket in the front end...
  20. Flat Bed Cutter Recommendations

    It really doesn’t matter where you hardware or software is made..what matters is where it’s supported from.
Top