Recent content by untitled

If you are using Flexi I've had a similar issue, but not exactly the same. Mine would be that when sending a cut only job from Production Manager it just wouldn't start cutting at all. If it's something similar to this you can try going to the flexi folder -->...

Yes the empty edge is where the perf cut goes. It also makes it easier to remove the sticker from the backing if the vinyl isn't all the way to the edge. My main reason for switching the blade is that it preserves a nice sharp blade for cutting the vinyl, whereas cutting the backing dulls the...

I usually leave an empty edge around my stickers that are cut out. So if you kiss cut then weed and then perf cut so that the perf cut is only cutting the backing it seems to work really well. For some reason I never get good results perf cutting through the vinyl and backing, but I have gotten...

The Order Confirmation has order no. 20453491. The Pick List has order SHNUA055, but doesn't include the other order number. The Master Packing List has both order no. 20453491 and SHNUA055. The Invoice has order no. 20453491. They all seem to have the order no. 20453491 other than the Pick...

One other requirement on the power is that they will want you to be very close to 220v on each line. The lines at my place were hovering between 235-240 and I had to install special transformers to get the voltage down to 220. Mine was a 700, but if I remember correctly the 315 would have been...

Go to the program files and see if there is a 32-bit executable there that you can run instead of the 64-bit. I'm willing to bet the 64-bit version won't work, but the 32-bit version will. File path should be something like this if it hasn't been changed ---> C:\Program Files\SAi\"Enroute"...

Ya for some reason I didn't even think twice about this. Usually everything I am cutting is larger and didn't become an issue really until I print/cut some smaller letters. That's exactly what I was thinking and I think I spent too much time trying to troubleshoot the offset and was stuck on...

I always set the offset on the cutter and not in the software. I think my screen shot I had it enabled just because I was trying all of these different settings. That is set in Production Manager, I will try disabling overcut and the other settings from the RIP and Print menus and see if that...

I don't know if I am missing something or what is going on, but I can't seem to get good results cutting from Flexi at all. It doesn't matter if it's print and cut or just straight cutting vinyl, the corners when cutting from flexi are always messed up and the cutting looks messy in general. If...

There is a guy at my squash club that I used to play with every now and then, he is a few divisions lower than myself, but we would play if we are both there for fun. Two of the times I rolled my ankle and sprained it when I was on court with him. The third time he was watching one of my matches...

So I just went through all this shit when I got my HP 700. The dealer asked for photos of the voltage coming from the outlets as well before they would deliver the printer. The outlets were right at 240v after wiring in new new breakers and outlets. They said I had to get the voltage to 220v on...

I'm confused. Are you actually trying to sell your chrome delete to a bunch of industry people?:roflmao:

Like everyone else has said go with separate machines. If you have the space available for separate machines do it. I have recently move from a Roland print/cut setup to separate machines with a Summa and I am kicking myself that I didn't do it years ago. Definitely way better.

Every vinyl is going to be different and also the blade depth / type of blade will also make a difference. But for a start I have a 60° in my Summa right now and my settings were in the attached screenshot. I did my contour cut first and removed the material and weeded it out and then put the...

I have been using the Contravision Performance perf for a long time. I have never used the campaign version, just the 60/40 Performance and HD Performance. I still have some 10ft x 90in windows I did I think around 3 years ago still up and haven't start to lift at all, I had just checked them...