Search results

there is not simply one component that fails. you need a service manual (and a bit of EXPERIENCE at this sort of thing) i have often found bad solder connections and "feed throughs" from layer to layer on the boards. damonc21 is probably the expert on these machines, the most important...

I am surprised. everywhere they have those posts to protect gas pumps, etc (every once in a while you get the careless or drunk driver gojng into the frontwindow of a convenience store.) the soda companies and cigarette companies provide these all the time

True enough, but i see them up EVERYWHERE. and my client will resell quite a few of these. with a higherpriced substrate it won’t happen. The whole project will just go away or theybwill purchase elsewhere

i have been ordering very little, with the wife hospitalized, so i had fallen away from ordering from grimco. thank you!

no, ideally it will outlive me. seriously, though, slit i side of the flute, in four places, making a rectangle, (the way the supermakets make end of aisle displays) then put a length of 2" gaffer tape on the inside, reinforcing the inside seams, and allow a 2 inch overlap, with banner tape...

we have been asked to make some "wrap arounds" for the pipe protecting gas pumps (see picture) can i get white coro with flutes running on the 4' dimension? then i can use a coro claw and slit one side of the coro and wrap around otherwise, what would you use to join 2 4' pieces together ...

power supply? much like an smc 4 or 4b, i would start by carefully reseating every connector, AFTER UNPLUGGING & waiting 30 minutes you can blow it all out with compressed air, wash the boards down with isopropyl, examine heavy pcb connections for cracks a service manual would be useful. (one...

if it is pulling vacuum you have a clog (vacuum showing on the guage if no vacuum (stays at 0) you have an air leak (loose connector, pin hole or bad oring)

my favorite tool when that happens...

https://www.amazon.com/gp/product/B0BXS2HK5Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1 we would use 2 of these @ $13/each works fine for landscape

if you don't have a perfect touch, you may need to finish with VERY fine sand paper (up to 2000 grit) and/or a good plastic polish

my fault for not taking the time to read the thread this close to the election, i just assume everything is trump/election related next time i will read BEFORE i put my 2 cents in

i like the way you think...

Oops,

https://www.google.com/search?q=how+many+employees+does+trump+organization+have+worldwide&sca_esv=f377f8634278135a&source=hp&ei=GOYSZ8ahH9680PEPlNbuqQs&iflsig=AL9hbdgAAAAAZxL0KJBk9dkY6H7niHcwyQS7XooKXTux&ved=0ahUKEwjGje77gZmJAxVeHjQIHRSrO7UQ4dUDCA8&uact=5&oq=how+many+employees+does+trump+organiza...

We are referring to trump here? he has 24000 employees all over the world. More than comcast & optimum together. Hiscompany has been around since grandmother started it in 1909. He knows something about creating jobs.

LOTS OF STUPID PRINTS? what are you doing? stealing my client base? i thought i was specializing in stupid

but they don't have $28./lb.chicken like we soon will

come on! you know perfectly well ALL judges strut around like they are philospher kings.. this is why the magna carta was written

did ink spill on board? or on ribbon cables? inks are conductive & cause a short. clean up with alcohol wipes. check carefully the ribbon cables, if one foil bent over and shorted you can cause a short then it is time to compare readings from transistor pairs & find the one that is shorted...