Search results

Anybody know why I’m getting blotches of less ink transferring? I’ve gone up in temp but not helping. Normally I’m at 200deg 55 secs. Tried 205-210 for 60 secs and some presses leaving streaks as per image. Tried orange pad, the beige foam one that came with press and nomex felt. As if it’s...

Can anyone recommend a cutter for cutting twill? Numbers and logos for jerseys? Is there anything that can also create stitch files? Currently I use Ioline 300 flatbed for both but they have shut down. If anybody uses a laser cutter how do you create stitch files? Thanks.

If anybody has parts printer selling parts I'm having difficulties locating these parts? they attach to maintenance base to lock carriage at home. D-31,32,33,34,35. I would also be interested in main board.

Anybody offer ink unlock services? My epson chip on main board blew. Had the board repaired with new chip , and couple transistors found faulty. Upon start up the same epson chip blew up, loud pop. This board was already assigned with files to allow me to use dye sub inks. Im in process of...

RCS screen was taken in to circuit board shop for diagnosis. Tech said he can power up the screen no problem but says most likely the board or chips were bricked during update. Without some sort of recovery software communication to turn it on will not go on. What a bummer.

Alright I see. Then I will try to locate Artisitc digitizer, or digitizer pro by Janome. Just curious as If I can use this machine with out my RCS sceen. thanks for your input

Janome mb4 was given to me but the Rcs screen will not turn on. Stopped working after update was told. I see that to operate the machine the Rcs screen is optional. manual says a computer can be used. Im unable to find a screen to purchase so wondering what kind of software will it need to run...

@ umca and Netsol without removing the transistors do these readings say anything? Or must I remove them all? Meter on diode. On hFE setting I get nothing. Also, my F4 fuse has erratic reading then ends at overloaded, rectangular beige fuse. F1 and F6 are identical fuses they are stable continuity.

I have some knowledge on electronic component testing. But not much with transistors. Will a multi meter suffice? Or will I need a oscillating signal generator tester? Can I get accurate readings with components still attached to the board using a hand held meter. Or must they be removed

honestly I do recall few drops of ink falling from damper on my head board. I just wiped it. I did clean it with alcohol second time around but Im afraid the damage might have been done already. I also installed new ribbon cables. So, most likely transistors then. Thanks for reply I can now do...

alright so focus on the main board then. Wasn't sure if I should check CR board or main board. Ill check the transistors. Thank you

i have same problem. mine was printing good until I replaced single damper. Now it will not lay down ink. Station is pulling ink. I replaced head cables and fuses no luck. Then I replaced new head, with new fuses again and it keeps blowing my F3 fuse on main board. 750 ma. Should I focus on CR...

if anybody can help Im out of ideas. Converted 1624 to dye sub ink. Did a very thorough flush. Lines are very clean. Install new dampers, M station and foil ink bags. Turn unit on all lines are pulling ink except one magenta. Did nozzle check and it is very good aside from that single magenta...

hey Yes , I have decent knowledge of it. I checked all the fuses on the main board and they all good. I have 120 volts coming to printer and main fuse. Main fuse is ok too. The first cable connector to power board is providing 120 volts. But onward of power board is my issue I think. On the...

No air bubbles. The one cayan channel is perfect. The other I cannot get it to work. Bunch of cleans and it comes back fully but then drops out again. I’d like to rule out ink as I’m on a new bottle of ink, new batch. I dunno!

It’s been a busy month with issues can’t seem to get on track. I dropped the front cover on my rj900x and the power went out. Cannot turn machine on anymore. I unplugged it over night and still nothing, as awhile back had a similar incident with losing power but was able to restart after...

ok nevermind I figured it out. When I select different wave effect that uses different head channels and disengages the plugged cayan channel it no longer sprays or contaminated the paper. In wave effect you have the option to select A channels, or B channels. of the head. Since one of my Cayan...

is my print head toast or something else going on but my prints have bleeding or ink migration past the edge of the print. As if fine dust of ink is falling or spraying the paper where there is no art. Its ruining all my prints. First I thought it was pressing issue but after inspecting the...

I flushed my cayan entire line with di water. Cleaner my cartridge entirely. Poured in new ink bottle of cayan. Installed yet another set of dampers. Had to do about 7-8 cleans and finally got my cayan channel back fully. Did several nozzle checks and prints and channel was good. Printer sat for...

I think you are right! It slipped my mind that few years ago my Cayan ink turned into a jelly substance. I then realized the bottle they sold me was expired. Yes, sublimation ink. I'm using Kiian ink. Only If I could charge or flush a single channel. Thanks