Search results

Ose fuji accuity has it moments too, show the tech that air is in the coolant lines ( very much ) and the say strange, but continue to fix head lamp problems,.

so what did you do to get it to work ? Also which inks are you using,...even if you have had no changes. Sometimes there can be bad batches especially if you have printed with the same file before. or possibly solvent mixing with the ink. How are your jets firing. Lots of gaps or are...

If you have done no changes to the motion.init file then the problem is more than likely the sensor for the capper tray. there are a couple of sensors for the capper. one inside the carriage , left side near heads that is suppose to look for the capper tray when it gets push up into the bottom...

Great news for you. Just make sure they support you 24/7 ( insist ) for the first while, Have seen a few installs that are great others really not so good. All printers need a bit of a shake down . Nice printer but you really need the flow and of course space. good for you ! :0)

You are going to have to do a little homework. Find out what type of work you will be expecting for this machine. What percentage of fine detail work ( higher res ) what materials , roll over sheet or more sheet over roll, what widths and types. How flexible the ink should be, White ink ...

Probably useless to you but why not try an Agfa supplier like ND Graphics,

First of all you have to understand that solvent printer have at least two problems,..... or more. Solvents are usually flammable. They off gas for awhile. Ink must be heated or fanned let alone vented outside. inks don't stick well to many materials. dot gain is also a problem. Environmental...

Yes there is no way to ask gerber, but then again as written above usually 2 years is ok since material give out as well as inks fade. Coating will help, who knows maybe this is also why gerber is getting out.

What a load of horse hooey ! Really brushes paint and talent for sign making, Geesum you must have some pretty uncreative people in your parts. The only signs around here like that are done with vlynle cutters and colored boards. Here we deal with art directors, creative agencies are well as...

Worked with the Fuji accuity for the last few years using ko inks. Ki inks have way better adhesion but are a little less punchy. Its an ok printer , we push it hard. alot of double strike and white usage. Overall its been good, not fast but good . watch the banding, and ink line kinking in the...

you could always try TCS uv lamps, make sure they are ready for install, they take your old ones and refit new bulbs

I guess you forgot about Symantec sam antivirus for the mac, common sense prevails

dongles are usually printer specific so you may be out of luck. contact Colorburst for a fast replacement or start looking around for the old one.

Yeah well that is a problem with Fuji,.. Of course OCE says that they have the best techs and they really understand the printers,.... blah blah blah,.... I have been told Montreal has the best tech ( while I was in Montreal ) then again when in Toronto the rep said the best tech is in Toronto...

Estops are the starting point but you said you solved this problem by changing the power board,...How would you know if you are now getting com errors,... ANyway when you changed power boards did you check that the little jumpers were all in the same place there should be at least 3 of them ...

do they move if you turn them by hand to get them started ? Do the rollers pinch at all ( up down ) Does it advance or go back with no pinch or material loaded ? Agreed , check safety switches,... is there a trip wire ?

Seen this with Fuji/Oce and with Vutek, thats the problem with RFID programming may or may not stick, programming may be incorrect, even seen mis ided colors, color that time out, etc. Also have seen where shop or near shop there has been a welder or rf welder been used that flake out these...

So what happened ? Did Fuji find the problem ?

Yeah that will work,... you just do not want to cut the belt or gash it, When the ink comes off it will look like the belt pattern, I use the back edge of a 1/2 inch wide exacto or retractable blade. I do it with the belt moving forward on a horizontal surface. Takes practice. Trick is to not...

You did say motor and cables, sensors ( height ) ,so check your carriage trip sensors, the ones for protecting the heads from hitting. If it fails on initial then you check what is being checked and eliminate one by one. Basically you have motion errors. I have seen that cables get twisted...