Search results

Center hinge...pray for little wind and some shade and you will be fine. Its only 2', so if you can split the paper and pull back small amounts at a time as you apply it will make it easier. Nerve wrecking, but doable.

Wondering if anyone has any tips/ideas on how/if unlaminated view thru vinyl should be overlapped for seams? I have some large windows to cover and I'm wondering how water will act on the overlapped sections since I'm sure the holes won't line up 100%. Is it better to leave the overlap or trim...

Thank you Sent from my SM-N950U using Tapatalk

Wondering what everyone's thoughts are for storefronts that want to use view thru window film. I've done a few, and some that have a lot of light from inside seem to wash out visibility wise Is there a preferred media or hole pattern for stores? I know vehicles are supposed to use 50/50, but are...

It's important. I thought it was a myth...then had some 12" x 18" aluminum signs come back. Funny thing was it only discolored in the areas exposed to direct sunlight. Ones in the shade did fine. Sent from my SM-N950U using Tapatalk

Does anyone have a source for bag signs? Customer came in with a u shaped wire frame and a thin plastic printed bag that just slips over it. I thought stouse... but no. Any help is appreciated. Sent from my SM-G950U using Tapatalk

I used a cleaner and polish in one...maybe a straight polish is the way to go. Thank you Sent from my SM-G950U using Tapatalk

Thank you, I will give it a go Sent from my SM-G950U using Tapatalk

Polish the doors? Not that you're an elevator service man...but any tips on this process? We talking turtle wax here or something bigger? Sent from my SM-G950U using Tapatalk

It could be...but damn that's quick. Any fix or cure you know of? Sent from my SM-G950U using Tapatalk

There was adhesive left behind, which rapid remover did get rid of. Door felt smooth to the touch, but a ghost remained. Wd40 did seem to polish it up a bit. Sent from my SM-G950U using Tapatalk

You heard wrong. Didn't make a lick of difference on this. Sent from my SM-G950U using Tapatalk

Wondering if anyone else has experienced this. We did a quick job for a local hotel where they wanted a logo on their elevator door for the weekend. Used oracal 3164ra film. After only 4 days, it was a bear to remove and left a ghost in the door. Is it something in the stainless reacting? Any...

Have a customer looking to have acrylic letters installed using a "UV bonding method". Is anyone familiar with this method? Sounds like Weldon to me?Any help is appreciated. Sent from my SM-G950U using Tapatalk

Invest a little more. The time saved over fighting with a cheaper laminating unit alone is worth it. We laminate everything for the abrasion protection as well. Last thing you want is to get a scuff on a new panel in route to a job site.... Sent from my SM-G950U using Tapatalk

Wow...thanks for all the input everyone. I have presented a few options...we will see how it goes! Sent from my SM-G950U using Tapatalk

Paint stores said the glaze with scrape off...that was my thought too Sent from my SM-G950U using Tapatalk

Think my customer is out of luck, but figure this is the place to confirm. My customer has a wood slat wall they want a logo stained on. Problem is, the slats come with a matte sealer on them. Pretty sure staining is out. They don't want me to sand the wall to let it accept the stain. Anyone...

Look in the cut menu and see if you turned on "return to origin" after cut. Happened to me once...now if i can figure out why it won't remember the page gap.... Sent from my SM-G950U using Tapatalk

Does anyone have a good technique for making an easel back for a "life size" foam board cut out? I usually just cut an angle and attach to the back with Velcro, wondering if anyone has a nicer technique? Thanks in advance! Sent from my SM-G950U using Tapatalk