Search results

Clean the lamp glasses first If the printer is not new. When installing a brand new Arizona 6170 Mark 2 I had a very pronounced such effect. Here the glasses were perfect. New printer. To a great extent, things depend on the inks and the material. Look for some mat mode. Try to align the heads...

I know :)))) Keep going and if you see that the ink seems thicker when purging or you start losing nozzles while printing, you will need to change the temperature through the printer registers. Two degrees isn't much, but it's still a difference. However, let's not forget that these...

Describe the problem please. The lamp system is different in 550.

But you did this so many years ago that I no longer remember when it was. :)))))

You can do this without problems. If you change the ink tags from 256 to 257 the temperature will change to 45 degrees. Now(256 is 47). It is not a big problem. By changing the temperature of the ink you will also change the viscosity of the ink. You can edit the registers and get the...

Clean the filters.

So ... 1. Remove the pump from printer. 2. Try to switch on separately from printer in line that you have good automatic fuse (220V). The cable connector is bigger than normal, because it is 16 Amps. If the fuse falls again and the machine is GT: 1. You are looking for a new or different pump...

The White is really good. There is no problems with clogged nozzles like in hp. However, Canon has a lot of experience with white ink. The only similarity with hp is that these are printers in general.

things are different here

What is this Arizona? 250, 350, 360, 550, 660, 6170, 12xx, 22xx, 13xx, 23xx??? GT or XT? Your question is not correct. If this is 250, 350 it is a little different. On 360, 550, 660 ... read this. If this is 6170, 12,22, 13, 23 it is different situation. 1. Change the position of the lamps. I...

Will be absolutely easy if you have the service key. Looks like non original ink but anyway. There is a lot of ways for that, but in this case(user level) the the easiest will be to buy this kit. I used years ago and don't know if it's still the same. I do this through the service menu when...

Why you want to clean this line? What is this flush kit? Give me the part number please! In UI there is procedure for this situation. To make something with ink lines not knowing what you're doing, can make things much more expensive than a service technician. Tell the story please! :)

Download Onyx Thrive from Onyx site, install it, install printer driver and try again. Will have 1 month for test. Next step is to change the router, cable, PC, may be LAN PCB in printer, LAN card in PC. There is cheaper choices for diagnostic.

Why in new theme? It is easy. Just find user manual for Arizona 350/360 and read it. The document is free and you can download it. It is too big for there. May be you have it with printer. This is one big white book. When you fill the coolant start the heating from user interface and plug the...

Yes. It is fact. Good luck :)

Remove it. It is normal if the printer is prepared for transport from Arizona service engineer. But it is not installed from him. Remove this bracket(just remove the screws), remove the two lower gantry covers(left and right). Take a look for red aluminium small red block's that fix the gantry...

No about clutch. Here we are working with closed eyes and we have to question you. So ... Is this printer is new for you(I mean new installation) or before this problem the printer was in working condition? If the printer is new and if it is not installed from service person and if when the...

When the power is completely OFF from the switch or when there is an error generated "Printer error" the servo doesn't work. You should be able to move the beam back and forth completely freely from end to end of the table. Likewise, you should be able to move the carriage along the entire...

2-3 cm is normal movement. Can you move the carriage and gantry beam buy hand(more than 2-3 cm when the printer is power of or after Printer error? If yes you may have problem with carriage encoder reader. If you have service key you can check this reader easy and for 1 minute. There aren't too...