New Guy Set up Onyx to make cut registration dots?

[ProdPrintMan]

New guy here. thanks for your knowledge, I have been looking thru the forum and learning a lot.

Onyx Thrive 19 to Multicam Router using enRoute.

is there a way to set up Onyx to auto generate registration cut dots? I have googled and googled and I have used a bit of chat gpt and google ai and I am missing something I think. I am thinking I may need an add-on for Onyx to allow Onyx to make those cut dots and save a cut file for enRoute to run on our Multicam. But I also feel like that add-on may be for running the Multicam straight from the Onyx rip. that is not what we need.

Our goal is to set up hot folders for our different substrates for our HP flatbed, and for Onyx to then create the print file with the needed dots, save the cut file to a designated cutter folder on the server, then be able to open those cut files in our enRoute software to cut on the Multicam.

that all make sense? bare with me as this is a bit of a new issue that has been asked of me to figure out...and it would be a great time saver for the shop and the design room alike! thanks!

 

[balstestrat]

Yeah you select the cutter and you get your file, pretty simple at the end.
You need flatbed cutter on your license tho.

 

[ProdPrintMan]

Yeah you select the cutter and you get your file, pretty simple at the end.
You need flatbed cutter on your license tho.

I have the Multicam as a cutter I can add in Onyx, but there are no settings anywhere that I can select the dots, spacing, etc, which it sounds like I should be able to do. So I do need that Flatbed Cutting Option Add-on then? It kinda sounded like that was only if you wanted to run the router directly from Onyx, but is that not the case? you need that add-on to also be able to add the cutter to Onyx, too? trying to figure out if we need to buy the $1800 add on. was hoping not.

 

[Tatonka]

I don't think there's an add-on (but I could be wrong), as long as you select the cutter in the file settings, it should automatically create the dots. Especially when using Thrive. You can dig into the settings in the cutters in Onyx (I think it's File>manage cutters) to determine what kind of workflow (mark type, barcode type, etc) you want it to use, and then in CutServer you tell it where to send it. I think it would be a pain to have it send it to different folders based on substrate. Generally it's set up for each cutter to have a folder on the server if you're using a barcode. For example, I have a folder for our Summa S2, and one for our Summa F1612. And then I have quicksets set up to select the cutter automatically depending on what I'm doing.

 

[Caren Hines]

I don't think there's an add-on (but I could be wrong), as long as you select the cutter in the file settings, it should automatically create the dots. Especially when using Thrive. You can dig into the settings in the cutters in Onyx (I think it's File>manage cutters) to determine what kind of workflow (mark type, barcode type, etc) you want it to use, and then in CutServer you tell it where to send it. I think it would be a pain to have it send it to different folders based on substrate. Generally it's set up for each cutter to have a folder on the server if you're using a barcode. For example, I have a folder for our Summa S2, and one for our Summa F1612. And then I have quicksets set up to select the cutter automatically depending on what I'm doing.

Here's a screenshot of what Tatonka is explaining.

 

[ProdPrintMan]

thanks for the explanation and visuals. can you tell me what version of Onyx you are running? we are on 19 currently, which may be of the age where the cutter settings weren't included, where as I think versions like 24 or 25 may have the settings included for flatbed cutting/routing (we have the Summa roll print cutter set up)...correct me if I'm wrong.




this is what I see when adding the Multicam cutter. it is listed in the available cutters to add, but when I go in to the settings, I don't have any where to add those specifics for marks.

 

[Tatonka]

the cutter mark settings are in the main Rip-Queue part of Thrive, not in the Cut-Server part.

Cut-server is where you control how and where the files CUT, the Rip-Queue is where you control how they PRINT.