Search results

Well order 3 more heads at $660 each $100. more than digi, But the one I order from this guy working good after I got vapor lock squared away.Thanks for that tip...really started to worry about printer being all screwed after the new head was on and loosing the right channel . I know Iam working...

I hear about the pressure thing so I didn't put too much on it I think, but kind of heavy handed like striping screws, making sure they want fall out .So how about cleaning solution on the electronic on head .If you get some on it rinse with alcohol and let dry for 24 hours right?

By the hour rate only..... if that's reflective and been on for a couple years it most likely going to leave the glue on truck when pulling vinyl off. Maybe not if you can get that right temperature thing going with heat gun.Price sounds good for my town, but everybody here seems to lowball...

If you can hand letter or going to mask it off I would use Jillbeans solution, that,s the way I have always done it.If its treated so paint will not stick use one shot vinyl primer,there is no telling how many cans I used of that stuff. Lot of work and need to watch the drips could get messy.I...

They told me to change manifold,that they sold me but not to purge..just put on and start to print.So after I clean them and good stream of spray is coming out are they still clogged? I will try another cable but the one I have on it is new and worked great on data swap???So on new heads what...

Was getting error 07 on rattled head. I dont know but the new head I just bought Is working great so far. The digi heads had 3 stickers too, but all the numbers were the same top, middle and bottom.New head no rank numbers

No break and they did not tell me to purge heads and I ask them if I should flush them with cleaning fluid and they said no just put them on. But I have clean them since and Iam getting a go stream of fluid coming out like they aren't clogged.What would make black change side..channels on data...

Looks like Iam going to have to replace all three heads from digi. Did data swap and new head fired on all cables. black just changed side -channels and cyan-yellow nothing. That was 4 heads from digiprint that was no good amazing. They sent me water base heads by mistake and told me to just...

oh yea..the new head must of been vapor locked because its printing great right now,never would of figured that one...thanks artbot & sightline

Well did data swap and the new head fired on all cables the black just changed to other side or channel. So that means all the heads I got from digiprint were no good.Plus black has lots of overspray,Still nothing out of cyan and yellow.Like I said they sent me one that had a part moving on the...

thanks I will

Iam going to have to get more ink so Iam going to order some pumps...planning on keeping printer until the paint fall off it if I can get it back printing. Ill well try to listen for the hissing today when I finish work.Have small roland sp 300v to keep me going.Good luck with your project,I...

this was the last print before it all started.

bad pic Ill try again bigger if not Ill take a pic tomorrow out side in the day light

Thanks that was driving me nuts..But this is what Iam getting on test print no cyan or yellow at all. Have new cap on capping station,didn't replace the station just caps...have not replace pumps yet

have the test print pic whats the trick to thumbnail it

Do not exchange the FPC between rows A and B because of power short-circuit.So that means I can swap just like black and magenta but dont cross a & b.... maybe its the arrows on the swap diagram that is confusing me???

Well I was getting this crazy test print so I pull all the cables from slider and main board and reset them and it got rid of that prob. But as I was taking them out I look very close at each one and they where set tight and straight in slot. bought printer used with bad heads, dried ink and...

ok just pulled ink on magenta getting ink on the other side now not 100% but better...pulled ink on black still the same

Think it could be the main cables from the board to the slider