Search results

thanks for the answer ( more info ) when I aarived, the cyan 3 was not printing,. -so first I check the capping station, it was clean and i got good suction between the cap and the print head. print a nozzle check and cyan 3 not printing. ( just a few little lines and fuzzy lines ) - did...

hello to all, I hope some one can help me with this issue. I am working with a mutoh blizzard or fuji maxjet. 8 heads. last weeek after the hurracaine in monterrey, the print head number 3 ( cyan ) stop printing. well it prints but funny patterns. first I tought that was the capping...

it can be the steel belt the problem just started, if you can print the nozzle check and if you send a job starts to print and then the error, is that the steel belt is about to fail, try to tense the belt a little bit. that normally fix it. I hope this helps

SID Printers same as challenger and Pheaton ( Made in China ) I dont know exactly how this peope are in service. what I can tell you is my experience with SID or Challenger Printers. They are good, fast printers, with good ink and a good RIP. you will have production and good quality. I have...

Hello to all. I am working on a Mutoh Blizzard 65 inches with Onyx RIP. on the brochure it says it can print up to 80 sq meters per hour. I know that if the press prints 80 sq meters per hour the quality will be BAD. But I need to show a customer that prints at that speed even that it will be...

hello to all. I have a tast to profile some mimakis, but they are using raster link 5. do some one has a how to profile, I have never used before this RIP. all help is welcome

there are few good ones for your mimaki wasatch, onyx, caldera or colorgate can be a good choices

the 6.5 and the 7 version dont match the version 6 and version 7 dont match you will need to create profiles from scratch or go back to the old version. the best way if you have an i1 create profiles from sctratch.

create a new profile you can create a new profile for the media or to re-linearize the media. production house allow you to do that with the eye1

colorburst with ultra vu 260 I have seen this before. its the format of the lin file. if you open a lin file already in the rip.( open with note pad ) and if you open the file of what you have red, the format is different. you will noticed when you open both files in note pad and compared...

hello to all, a few weeks ago i installed a complete capping station into a mutoh blizzard and now 3 print heads are not ( printing ) i use a syringe to draw ink from the lines but, I only draw air. any suggestions. all the dampers have ink.

dryer plate increase the dryer to max temperature to dry the ink. how many heather plates do your printer have.

hello to all, does anyone service fujifilm acuity or oce arizona 250 gt. I need help , problem with tilted carriage. Thanks

for ink try sericol ink NH series, is working like a charm on XL printers.

what printer do you want to use Hello what printer do you want to use to print the styrene. what inks do you use. you have to turn off the heat on the pre area and printing area, then you have to use the front take up to have tension to avoid any bulk on the printing area so avoid head...

hello i tried the site but I dont have password any other help wil be great. Thanks

probably a solution. I had a problem similar to yours. I had to replace a main board of a mutoh PJ 2.6 due that the chips that send the voltages to the motor were burned, I also change the cr motor. so I cross by mistake the cables that connects the cr motor. so everytime I initialized the...

the mutoh pj are good printers, the parts are quite expensive. the printer that it has been offered to you it is a mutoh PJ is dressed like fujifilm vybrant or vutek. ask them what kind of ink did they use. you can make a nozzle check pattern. check the firmware if it a mutoh firmware, fuji...

Hello to all, does anyone have or had worked with a mutoh PJ 2.6 solvent press so we can share information. Thanks. I have a problem with a CR overcurrent error. I have replace many parts and talked to mutoh , but we can not figure out what is the problem exactly. Thanks

Hello to all. this is a very interested forum, I hope we can share information to help others with problems and find solutions.