Search results

The difference is not only 3 instead of 4 pinch rollers. There is a difference in the grit rollers too. The Latex 54 Cutter coming with the 315 have one wide grit roller, so it is possible to arrange the pinch rollers for nearly every media width. The Latex 54 BASIC Cutter have small grit...

Replace the maintenance station. Most of the time this symptoms are the result of a capping which don‘t work properly anymore. Should be replaced once a year.

The i1 was originally developped by a swiss company named GretagMacbeth. This company and the technology is bought by XRite several years ago. The technology is compatible, even if „GretagMacbeth“ is shown up in the software, as with the i1 Pro 2 too. VersaWorks only supports Linearization, no...

Set the Printer to DHCP for a moment. The printer will poll the correct data. Set it back to Manual, the printer will remember the polled data. Set the right manual IP-Adress again.

Never heard of that the FC8600 can read barcodes.

If having reading errors with barcodes, make shure you check the following: be shure that the barcode is completely within the outer pinch rollers, or the cutting width is extended with the „extended load“-function (can be found in the System Setup - Actions-Menu) Do a media calibration (system...

It will work. Flexi internally doesn‘t manage cut contours by colour name, but when using the cut contour tool, it defaults to a contour colour which is correctly named for use in third party rips. If unsure, you could select a spot color named „CutContour“ in the design centrals color chooser...

As long as printing without profiles, your output specially with photos will not improve. Unfortunately, because of the age of your printer, it will be hard to find any compatible Profiles to Flexi 10. When the SC500 was an actual printer, there were profiles available for Flexi, but this...

A cool feature of the Latex 500: Wiper Roller. A roller which cleans up media before printing. Had a similar problem with a cheap vinyl ... runningg it with the wiper roller works fine.

HP uses a different Barcode type, but the barcode functionality is available on Summa Cutters since the introduction of OPOS X in 2005. I don‘t know why HP have re-developed this functionality, specially on coloured vinyl the original postnet barcode is better. Have tried to calibrate media on a...

Or you can buy a HP Latex ... they have it factory installed, can be switched on and off through the touch screen, and the printer itself can switch them off temporarily if the light could confuse sensors.

If you say you get "offline" if printing a barcode, does that error message appears when printing? That is a complete different issue. Where do the message "offline" appear? What do you mean with "checking the IP adresses of printer and cutter"? Does the printer print? Does the cutter cut if...

Download the installation file from www.onyxgfx.com , start installer.

Had more than one year nutricional advice and have lost 17 lbs, than gastric bypass surgery ... have lost more than 110 lbs in 9 months.

You don‘t need to switch it. Thrive is a network licence, just install on the other computer.

It is not a problem of the RIP-Software, it is a problem of the printer and/or the media. Different conditions (temperature, air humidity, production charge of media) could lead slight different coloration. If you have the newest firmware installed, you could switch on the "long run consistency...

The media length calibration will be saved to a user configuration. So you can do up to 8 different length calibrations.

How to set up FlexCut-Parameters in the cutter is described in the user manual which is downloadable on www.summa.be. How to set up Flexcut in Flexi depends on the version you use,

Depending on the printer, if the middle of the print is not exact, it could be a problem of the media, an effect named „bowing“, comes from applied heat while printing (the media is distorted). If your Cutter is a SummaCut R-Model (dark grey instead of beige), you can set your Cutter to OPOS XY...

There is an option in the Print Quality menu named something like „Optimizing colours and text sharpness“ (sorry, I haven‘t the english name in mind because the machines we sell are mostly set to german, french or italian language). It is the last item in the image quality-menu. If it is set to...