Search results

I am printing on perforated window film with optical clear overlaminate. My question is...can you heat stretch this when applying it to a convex or complicated curve? I often start to get creases towards the edges on curved windows that I have a hard time getting out. Any suggestions?? Thanks in...

the pass count is usually where the print mode is shown on the image. I think because I am using a different media. If I use HP then I have the option of choosing the pass count. The media profile I am using is for Oracle because I was told to use this icc profile for the backlit media I am...

print mode is = CMYKcm

We have a hp 260 latex printer and are printing on an adhesive back (backlit) vinyl and I am wondering how do I get more vibrant/ popping colours and how do I keep the look of the graphic to be relatively the same when it is not lit as when it is backlit. And how do I get my black to be opaque...

I found where the hard drive is located. (it is missing) It is located in the lower part of the printer at back. It is a separate unit that contains all the ethernet connections however It does not connect to the printer directly. It has connectors (see photos attached), that I do not have a...

Thanks again SightLine, It is ironic that I do own a phaser 7750 also!! Works great! Here is a photo of the back of the machine. Is this where the harddrive is? or should be??

Thank You SightLine for the quick response! Couple more questions. 1) How do I know what the other alternate model numbers that would be the same as my workcentre Pro 255? 2) where would I find the hard drive? (to be able to access it and recognize it) I just finished taking the entire power...

Anyone know where I can get a FRE downloadable copy of a service manual for xerox worcentre pro 255?? I've seen sites where I can buy them for around $14 but would prefer to get one FREE. I bought the printer at a Police auction and it is not powering on at all. I romoved the back cover where...

I do not have it on. But I did notice that my printer takes a half inch off of each side to allow foir media holders thus bringing my media width down to...."smaller than 48"". So what I am trying is... loading the media manually and fooling the printer in thinking the media is a little wider...

Hello, I am printing a 16ft X 8ft billboard onto white reflective vinyl then applying onto a 3mm Alumet 4X8 sheets. My reflective media is actually 48.875" wide and my sheets are 48.03" wide. The issue I am having is when I set my overlap settings to...(0.25") it always seams to TAKE OFF the...

Thanks a lot JustnTym for replying, We did do a number of checks with our Tech support team. They were extremely helpful. We ended up having to change 7 heads the last few weeks. (they were due) however that did not correct all our problems. We also had to change all 5 bearings on the carriage...

I recently changed 4 heads on my HP45500 printer because we were getting bad results. (( getting intermitent printing...like leopard stripes in the consistency of the colours )) Did a "prime Bar" and all the heads are good but I still get the "blotchy striped" printing. Any idea what would cause...

I got it going last night Finally!!! I did just what you stated and it turned out super vibrant!! Thanks

sorry OK, sorry. I was not aware. I only wanted to make sure it was seen by as many people as possible to get the most help possible. Thanks, dennis

return to origin OK., but who is to say the registration will be exact. I will try. Thanks, dennis

anyone have any idea how to print a backlit on a clear poycarbonate on the HP45500 UV flatbed? There is a setting for backlit roll material (which works absolutely awesome, beautiful vibrant prints), howeveer ther is no setting for printing a backlit on a rigid sheet. I tried creating my own but...

thanks thanks Craig, I will look into that and let you know.

Hello Craig we spoke via e-mail yesterday in regards to equip. I have for sale. anyhow....I just started this print and cut and this is the first intricate die cut shape and it is going off about 1/2" longer than my print. It does the same with and without the lamination.

I am printing with HP45500 UV printer and cutting to my "Graphtec FC4100-130 plus". The cut line go off. (longer than my print). I checked the calibrating on the cutter. It is good. The printer as well. Anyone have any ideas why this is happening?? hELP!!!!

Can anyone help me out!! I can't get my cutter to cut a die cut shape. I design in corel x3, export to an eps file, I open the file in my onyx postershop ver. 7.3, then print to my HP45500 UV printer., then TRY to cut to my Graphtech FC4100-130 plus cutter. I checked that my hairline pen...