Search results

On which media do you want to print on? The problem is: for printing on vinyls, banner and so on, a built-in media heater is needed. The CJ540 (Cammjet) regularly don't have one.

If installing Onyx 11 on a computer with installed older onyx, the installer copies the settings and profiles from the old version, but will keep it alive. I had some problems with that driver and profile conversion, easily handled by installing a fresh driver and reload the profiles only. I...

I have tested the 480 on a L26500 and L28500, and have created profiles (Onyx) for both machines. The printing results are very nice, but I haven't tested stretching it. I know people who uses 480 for car wrapping, but have no feedback about that issue until now. Regularly, Latex should be more...

Will be difficult, because of the structure of the Mesh the i1 will fail measuring. There are measurement devices with a much bigger measuring aperture than the i1, perhaps they work, but I have never tested it with our Barbieri Spectro LFP (2, 4 and 8mm measuring apertures).

I search for a very light Tyvek or similar media (waterproof and tear resistance), preferrably below 90g per square meter. There is something around in 75g, but only sheets for HP Indigo. Should be compatible to HP Latex. Does anyone have a suggestion for me :smile: ?

The user manual is only talking about Print/Cut-Jobs because this is the only thing which can be done with Onyx and the CutServer. If you want to to print and cut-jobs in one software onyx is the wrong choice. Does the printer work with the printer drivers which are coming with the printer...

There are two flexcut-modes available in Summa-Plotters, "fast" and "accurate", and "accurate" does that little steps (stops everytime when changing pressure). Since Onyx 11, Onyx too supports only "accurate". When asking for that issue, they told me that skipping the "fast" mode was a...

Try the following: On the right side of the printer, below the window at the front panel, you will find a small silver tube (enclosed picture shows the same situation on a 280). This is an infrared temperature sensor. If possible arrange your print that the sensor do not measure on printed...

No.

If you plug in the cable incorrectly, you damage the fuse as soon as you power up the printer. In 99% of the cases, it's not the head.

I don't think the heads are ruined electrically, but changing head cables when the machine is powered on or just simply still connected to the power source will kill the head fuses which are soldered on the mainboard. The fuses are looking like the marked ones on the enclosed pictures (but...

On the L26500, check your printheads. If the age of the heads differ very much, this could be the reason for different colours with the same profiles. Color matching between different printers: there are RIP's on the market who are allowing to let different printers simulate a standard gamut...

The 545EX should be older than 2009.

To avoid that the software overwrites the cutter settings, you could configure the plotter to ignore tool commands sent from the software (communication - tool command - ignore). But this will not be helpful if you want to combine sometimes kiss-cut and flex-cut in one job. I don't know...

Yes, on the Summa the same knife in the same position is used to do FlexCut (Perforation). With the Graphtec, the same knife is used on a different location ((I don't know Graphtec so much, but I have checked the documentation). But the Summa is developed to do so, FlexCut is supported since 15...

I have done tests and profiling (Onyx) on both L26500 and L28500, and it works fine for me

The issue is about CMYK-Spot Color Mapping, what means using spot colors in the document to print exact CMYK-Values (according to a CMYK-Swatchbook printed out of the RIP). @ Tony C: I would like to see Screendumps too.

How do you export the data from Flexi to VersaWorks? Are there colors shown in the list in the "File Format"-Window? How do you recognize that the colors are wrong?

If the output values of colors selected from the Color System Library Palette changes in printing, I'm shure you have forgotten to activate the color replacement (tab "file" in job properties).

It's not Caldera, it's OPOS-CAM who don't support OPOS Barcode. So, if you want to use OPOS Barcode, you have to buy the OPOS X-Machines. Supporting RIP's are for example Caldera (as far as I've heard), Ergosoft Posterprint, Onyx Postershop/Productionhouse/Thrive since 10.2, SAi Pixelblaster/GMG...