• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

perf

  1. 70/30 Perf/vision print Curling on R-1000 - Help

    We are running econoview 70/30 Perf (vision print) on our HP Latex R-1000. For the life of me i can not get the vinyl to stop curling up BAD on the edges as it comes out. Bad enough that when i stop and it returns the vinyl back to the starting spot it is curled up enough to trip the head crash...
  2. Need Help Perf Cut Woes (Graphtec 8600)

    I'm having trouble with perf/flex cuts on my Graphtec 8600. My kiss cuts are pretty much fine - they're off by maybe 1/64 inch on the x axis and I can work around that for now. On the exact same file, though, my perf cuts are off by almost 3/16" on the x axis. I have a picture attached if that...
  3. Question Roland GR-420 : perforated cut - horizontal lines differ from vertical

    Hello I am trying to find good settings for perforated cut of the baking film (only the film, not the adhesive upper layer) of Siser ColorPrint Media. Using ZEC-3075 blade with the fin. I noticed that whatever settings I supply - the horizontal lines seem to be getting cut "more". For instance...
  4. Trapezoid windows

    We are installing 6 large trapezoid shaped windows from a bucket truck for a local printer. Laminated perf. Our first attempt was aborted because the printer made the prints the wrong size. I attempted to tape up the first piece, and it was way too long. The prints are heavy and difficult to...
  5. Need Help Red Or Blue Blade Holder Graphtec Fc8600

    My plotter came with the Blue blade holder and the CB09UB blade. I Often use the perf cut feature and have read it would be better to purchase the Red blade holder and some of the CB15UA blades and swap them out when i go to do the purf cut. Does anyone have any experience with the red over...
  6. Signlab 9.1 for versaworks

    Hi everyone, and thank you for allowing me to be a part of the community! ok my question, is there a way to set a job up for perf cut? its a pain to send job to illustrator to add the perf cut line so im wondering if there is a way to do it right in signlab? i use signlab 9.1 print & cut, and...
  7. Window Perf Cracking?

    Has this happened to anyone? This is a back window of a van, slightly curved. We used Cast perf, with a cast laminate. Learned that after having to redo it from the first time when the installer got a bunch of wrinkles from the laminate. The cracking in the pics shown happened in a course of 3...
  8. Flexi-Graphtec perf cut shiift

    1st time trying to make contour cut and perf cut for a decal, so bear with me. Flexi print and cut 12, Graphtec 8600. I have a simple circle for a test. Drew the green circle in Flexi, added 2 contour cuts: one just inside the edge of the green to cut just the vinyl, the second one is 1/8"...
  9. Window Perf on Store Front

    Hello, I'm creating some window perf graphics for a local salon's front windows. I have all of the artwork ready to go - but I'm not sure on how much bleed I need to add before sending it off to the printer. My boyfriend is new to installation process - so I want to make this as easy as I can...
  10. T

    Looking to expand into printing & installing window perf

    Hey I have seen some threads on here with some talking about how easy window perf is to install. Having never done it before, I am interested on experimenting on myself before diving into it. My F150 has a solid back window so this should be more than simple... right? Any advice on material...
  11. 20" Perforated Vinyl

    Hello All! I have 18 rolls of perforated vinyl that i am selling. They are cut to 20 inches wide x 165 feet long. This can be used for a range of projects including outdoor applications with a laminate. I am located in NYC and can deliver within a 30 mile radius if purchasing more than 9 rolls...
Top