Search results

we are gluing a thicker wall pipe to a thinner wall tube with a slip in piece connector between one side has a clearance of zero and the other clearance of 1/32 we can overlap as much as needed but i was planning on 0.75"on each end of tube

I've ordered some samples of each, which one is better 3m 8116 vs lord 406/19? my application is for gluing telescoping pipes together we have been welding the pipe, and the welds dont' look great, even if we invested in a rotating weld positioner, I think gluing would be faster and...

should cost about $300 for 1000 feet I use eastern metal but they do not carry 5/8" aluminum angle, just 1/2 and 3/4" 1000 ft of 5/8" angle would be about 100 pounds. Since canada is a huge country and we have no idea where you are at you can probably just order it from anywhere and get it...

i go the replacement parts for free installed them and the saw works fine again. for those of you that need a track saw occassinally or do not need to cut more than about 1" thick material at a time, this saw is very nice and on sale use coupon code below $250 shipped. Track Saw Price...

perhaps perhaps you are right, but my guess is I've tested the tool to it's breaking point and now know when it will fail and will not have future issues. It's 9amp motor vs the 12amp motor is a disadvantage, but it is also half the price. And I'm not here to say anyone is foolish for buying...

burned up the motor today SO I WAS cutting a mere 4 sheets of 1/8" thick abs, total of 1/2" thick, and i burned the motor brushes up. The carbon brushes overheated and one of them melted the plastic housing around it, causing the motor to fail. I called up grizzly and order the new brush and...

3 sheets of plywood is not the same as 20 sheets of polycarbonate First photo shows the material I was cutting 2nd photo shows the damaged bushing. IN fairness I was cutting on a piece of warped plywood as a base with a piece of 2" styrofoam on top, the uneven surface was the #1 reason for the...

Im sure my saw could cut loads od diabond that is only 1/8" thick it cut through 1/2" of polycarbonate no problem 1 3/8" will cause problems though i order the $2 part and the $8 shipping fee today for a tool i use a few times a month it will work fine

broken cs55 afer cutting about 60 sheets. i was cutting 20 sheets of 1/16th thick polycarbonate today. The saw had kickback even at the slowest of speeds. Now given that with the protective wrap it was probably 1 3/8" total thickness that is pushing my luck. I did 4 or 5 cuts and put that stack...

i GOT THIS http://www.ebay.com/sch/i.html?_sacat=0&_from=R40&_nkw=Scheppach%20SAW&_sop=15&_udlo=30&_udhi it is a scheppach cs55 track saw about $200 shipped. just used it to cut 8 sheets of 1/16th polycarbonate down to 4 sheets about 14x36" in size. worked just fine using an aluminum/plastic...

Thanks!

i don't understand differences? I've gotten samples of senstart and belbien in the mail. I've been told it is the same stuff as 3M dinoc. All of them are PVC films from what I read, basically thick contact paper with a more durable surfac.e I guess I will have to requrest some samples of...

96 cents a meter sounds better, but the minimum order is 6000 meters! from china pvc-films.com 96 cents a meter sounds better, but the minimum order is 20 rolls at 300 meters each or 6000 meters total ! from china so order total is about $6,000.00 Or I could buy it from the cheapest "USA...

eastern metal suply Easternmetalsupply.com sells the sign blanks for your common octagon stop signs, triangle and rectangular yield signs. My guess is ordering the blanks from them locally and then getting vinyl applied locally would be the cheapest method of mass production?

other supplier cool thanks for another lead. I'm also going to try buying direct from china http://www.pvc-films.com/products/PVC-Wood-Grain-Film-25-1.html i'm getting some samples mailed to me, hopefully the quality will be good for...

too expensive. unfortunately they told me I had to go through a distributor and webdon in charlotte, nc wanted $137 per 4x8 wood grain sheet. I asked if they did quantity discounts, and they said no. That is $4.28 a sq ft. Their door skin refinishing system was about $96 per door side or...

thanks thank you so much I will call them on monday to see what pricing is like. I dont' see any distributor links so I assume they sell direct, and they are only a couple hours away from me! Again I really apreciate the lead. Hopefully their prices are reasonable.

Before I started in the sign business.... I was familar with Contact paper and more durable substances like Formica. I just discovered ( I'm sure it is old news to a lot of you folks) architectural films. They are like thick contact paper with a hard formica surface. Only problem is their...

thanks cool this was exactly what I was looking for at $3 to $4/ sq ft it is a bit more than I wanted to spend, but I'm sure my customers will love how it looks. Hope they are willing to pay an extra $400 to wrap our booths in this stuff.

I'm going to make a projection table for a client that is portable. they will use it with microsoft surface technology/software to display photos on it. It will have a sturday aluminum frame with 4 legs, one in each corner about 42" tall from the ground. typically it will be set up for 5 to 6...