Search results

this is the second time my dx5 head stopped working, slowly losing all nozzles with every clean. Upon removal of head noticed ink/air is leaking from the side of the shiny face plate. The plate that has the 360 nozzle holes. Ink is seeping from the edge of that plate. Not sure how the face plate...

I had a spare new dx5 that I installed along with new dampers, several long cleans and ink fill and all works now. I dont have an explanation on why it is working or why/how new dampers would make a difference. Anyway maybe the printer being unplugged for several weeks reset the printer...in...

Yes I checked F3 ceramic it is good. OK!! Yes I starred at the CR board today thinking what could I check on it but was not sure. Appreciate it!!

My Rj900x had a head strike with the paper when the paper roll came to an end. The head stayed in that position over night so not sure if thats critical or not. After rebooting now the printer prints but no ink is being laid down. The head is not damaged as I installed it in my Vj1304 and it...

I would like to flush my Mutoh dx5 head used for eco solvent to accommodate dye sub ink. Anybody know if the butyl cellosolve+acetone formula would do any harm to flush it? 4:1 or 5:1ratio? I would flush the lines and install new dampers.

Using wasatch 7.4 and suddenly it no longer works correctly. But only on the 4 pdf files I need done. Files are ripping in the rip queue but not moving to the print queue. If I restart wasatch the files now move to the print queue and printer starts printing by itself. The only issue it only...

Just get the printer unlocked. Ive done it on my 1304 no more chip cards.

Yes I did contact them few days ago still waiting to hear back. Praba Printer out of Indonesia has it for $14 free ship...will give it a try. Thx

Canada , Alberta probably not one near. And if so guaranteed 800% mark up. Will call around thanks

SP540v model. The cable broke right inside the terminal. Im not sure if the cables are supposed to be not touching or not? I did try and connect 2 wires to terminal but still service code at start up. not exactly sure what is going on inside the terminal. Looked as though the 2 wires were...

Can anybody tell me where I can get thermistor cable for dryer? Its my first roland printer and I would like to get it going. First need to get past my service call 0121. The cable to the little screw is broken. SP540V. Thanks

Thanks for your reply. Makes sense. I def need damper replacement done more frequently. May I ask you one more question? PDF is correct format? CMYK? 150DPI? Thanks!!

Hello just wondering which would be a more probable cause of color shifting during very large printing eg. apparel printing. Low quality ink or printing in RGB? Mutoh RJ900X. I cannot achieve certain colors printing CMYK but little worried to try RGB again as it gave me unstable colors in the...

I bet you tubes and lines in the cap, cap station and going to waste tank are all plugged. Ive had this identical issue was able to remove and clean in few hours all worked well after good clean. printer cannot sit unused for very long. I add cleaning solution to my cap station several times a...

Ive been using black connector prin heads for years with no issues. Thats my dye sub printer. If its solvent ink I believe you must use green connector.

Did you have any luck with 9900 and dye sub printing? I need a back up printer and have access to a 9900. Were you able to run only cmyk in 8 channels? Thanks

Hello Im used to doing cut and saw print/press and never had this issue but when I press logos on premade garments there is always ink pressed on edge of my transfer paper. Ive tried everything with no success. More pressure, less pressure, taping paper with teflon tape. I use tacky paper...

All resolved. My inks were not stable. Poor color consistency. Soon as I paid for a high end ink all good now. And what Andy said above smaller pieced need less dwell time as they heat up quicker.

Thank you, you nailed it

yes exactly. Do you recommend just kepping designing in cmyk and eliminating rgb? I always get nicer colors in RGB design.