Search results

I would check the IP-Adress of your Versaworks PC if it is still in the same subnet with the printer (first 3 number groups identical, the fourth different). Regularly the printer is used with a fixed IP, while PC‘s are often configured for DHCP ... if there are changes in the network...

Regularly, if calibrating all machines carefully, you will have maximum color accuracy for each machine, what should lead to near conformity of the output of all printers. But there is still potential for color deviation because of different color gamuts of the printers and inks. There are...

It is not a hardware problem, it is a software problem. Both plotters needs to be recognized separately, but they will conflict if they are the same.

I have switched off the RIP-Controls, does it always through the printer controls. The sensor who scans the line is the OMAS-Sensor, a little rectangle who flashes red while printing below the media (does feed calibration too). A little mark on the back side where the lack line is would help...

With Summa, it is possible to connect up to 4 plotters with USB to one computer by setting it to USB1 to USB4 in the USB-CLASS Menu. Perhaps there is such a possibility on your cutters too.

You can‘t edit any ICC-Profile, you need the measured values to create a new one with different settings. And you dont have this values from profiles not made with the onyx profiler. Check your greys under daylight ... could be a big difference.

You need to set a sheet media instead of a roll media (you could create one in the printer properties through „Manage Printers“), and select that media when printing. The length isn‘t important as long as only one copy of your posters will fit on that sheet ... it will be cutted after the print...

If needed, the Barbieri can be used with the i1 Profiler Software too. We have a standalone licence of i1 profiler, no idea what this will cost. We have an i1, a Spectropad and a Spectro LFP in our company ... whenever possible I prefer using the LFP.

A suggestion will depend on what printer and media you use. If you want to make profiles for vinyl or paper only, a XRite i1 Pro is ok (you don't even need special software if using Onyx for calibration). Find information here: https://www.xrite.com/categories/calibration-profiling/i1basic-pro-2...

How do you have solved the issue with the vinyl cutting?

Do you know the 365? If yes, then check out the following video to learn the differences:

You need to use calendered vinyl and laminate for your application. And yes, this media is not cheap.

You can print any media size between 500 and 1372mm ( 280 to 1372mm when using small media mode)

When replacing the dampers, the following is important: Pull them carefully vertically upwarts from the connectors at the printheads manifold, because otherwise the connectors could break. Put the new ones carefully back in place. The ink will move back through the ink tubes. The most secure...

You should replace the dampers of the MY-head.

Could it be that some light sources irritating the media sensors? Had that some time. Have you moved the cutter to a different position? There is no need to tape the sensors, it is possible to switch them off (S-Class both or the front sensor only) or to calibrate their sensitivity (refer to...

I don‘t think that it is a problem of the speed of the network connection that the camera works with USB only. The USB-Connection is v1.1, with a maximum speed of 12 Mbit ... the network connection is 100 Mbit. Regularly, cutting plotters don‘t need high transfer speeds because the plotting...

All of the mentioned printers are very limited in the use of rigid media (weight, thickness, no borderless printing and so on). The Roland is based on a Soljet-Printer introduced to the market more than 10 years ago, as far as I know it still uses DX4-heads. I would think over carefully if...

You need to take the head out of the machine to replace the manifold, otherwise you cant reach the screws.

So it is a SummaCut OEM, no problems of this kind known. Check if the network cable or USB-cable is in contact to the metal media rollers at the back of the cutter. And if so, hold it away from them (there is a clamp delivered with the plotter which can be taped on the plotter to guide the...