Search results

I am at my wits' end! Printing on a fresh roll of Oracal 3651G, same as always. - Nozzle check is OK - Spit pads are new - Wiper blade has been OK (do they fail catastrophically all at once??) But for some reason, pls take a look at the pics!! Thanks in advance to any and all Signs101 pros...

I have a customer request for logos to be printed on car cover panels, prior to stitching and final cover assembly: The fabric is 100% polyester. 7.5 oz., 600 x 600 woven There will be 2 (possibly 3) logos per car cover. Quantity is 70 car covers - I have a Mutoh ValueJet 1624 and Seal Base 62...

My Kona Cutter seems to be on the ropes... Just will not perform a good cut no matter what. - Although the test calibration cuts come out perfect and there is a brand new blade installed, every time I perform a job cut I get a partial cut through on the vinyl and the blade's indentation never...

So I come in a little late today and all over the floor is the remaining ink from our 1624 large capacity bags. Machine has error, "waste tank full" but that clearly did not stop the machine from doing whatever it was doing until all the bags had emptied and overflowed onto the floor. I suppose...

Hello Flexi experts! I have a large trailer logo about 125 x 50 inches that has a contour cut applied to it. Since this is going on an old, riveted trailer, I would like to cut it into 3 length-wise sections with two 1 inch overlaps for the 3 sections. It has already been setup for a contour...

I have a job to wrap a C6 Corvette's front & rear quarters, doors and nose with matte black. I'm looking at: 3M CONTROLTAC OPAQUE FILM WITH COMPLY ADHESIVE/ECONOMY WRAP VINYL MATTE which can be seen here: 3M Controltac Opaque Film with Comply Adhesive/Economy Wrap Vinyl Matte | FELLERS - The...

Curious to know if any of the experts on this board have tried hot laminate on materials that are sold/spec'd as "cold laminate." Reason being we have experienced delamination of the clear top on a couple of jobs, particularly on trailer in the rivet areas. Just curious whether as to what the...

It is an Allen Head. Found on the floor under the left end of the Seal Base 62 - Anyone know where it belongs? Thanks in advance!

It is an Allen Head. Found on the floor under the left end of the VJ1624. - Anyone know where it belongs? Thanks in advance!

Regarding damper replacement for the VJ1624 - anyone tried anything like this: 1624 dampers | eBay Thanks in advance for any replies! also: Mutoh VJ-1618 / VJ-1608 / VJ-1638 / VJ-1614 / VJ-1624 / VJ-1324 head Damper | eBay

I have a Mutoh bulk ink system on a VJ1624. I'd like to try some generic ink bags; does anyone have an experience-based recommendation for a quality replacement that will save a few bucks? Thanks in advance..

Anyone know why flexi is adding a white panel into my print job? (please see attached image from production manager, blank section is 3rd row from the top) - It is a 57 foot long wall job. As always, thanks in advance for any replies

Related question: Anyone know if flexi 10.5 can read flexi cloud files? thxx.

Any opinions as to flexi 10.5 vs flexi cloud? My contract on cloud is up for renewal and I am just wondering if it is really that much better. - 10.5 actually seems to run faster, besides which I do not really use any of the cloud features. .. Anyone got an opinion about cloud vs 10.5? Thanks in...

I am getting the "Life Times [Pump]" message on the lcd of my 1624. I have read a few posts about this; can anyone tell me the specific component that this message is referring to? The message has been on for a while now, so I probably need to do something about it. Thanks in advance.

I have a wall job for which I am considering arlon dfp8000 However I see it is non air release - In the past drywall installations have been fairly simple but this one is a very long wall and the design will have much alignment Can anyone suggest an alternative to dfp8000 that will...

I am replacing the capping station on my 1624 which will be here tomorrow. Anyone know a good method to protect the Print Head while Capping Station is out of the machine? My concern would be for drying out the head nozzles. Thanks in advance for any replies.

Anyone have a tip on unclogging stubbornly clogged (red) nozzles? - Some times it clears out then comes back clogged a few days later. -Any advice greatly appreciated! Thanks in advance.

Anyone using SignLab 10? Love it? Hate it? Thx.

I have a question about wall mural material selection: - I've been using IOM with mixed results in terms of hard surface adhesion. It has been OK in some circumstances, not OK in others. Certainly IOM's price is right - a bit of experimentation is not a problem with their media and this is...