Search results

i check the pdf, no information about how to enable 3L option.

that sounds right. but the 3L ink system has been connected to the printer, how to enable the 3L ink function? i can not find any useful information online.

they are just like the other 360 manual option. no 3L.

Hi, I got a 2nd hand HP Latex 360 with 3L ink, It prints well as normal, but there is no option to replace 3L ink in the front panel. how can i reinstall the manual? The level of K ink is 575ml now, will the printer refill the cartridge automatically when it is less than 500ml? Firmware...

After many tries, the printer damaged 2x Power Supply Unit, 1x Heater Control Unit. 5xPrintMech Board. No. F14 SMD on the PrintMech Board is keep failing. it turns out that rainwater leak into the foam which is attached to the back of curing modules cover. that damp foam cause the short...

It works! thanks. load the vinyl as 'Canvas', do the colour calibration, then load the canvas to do the ICC.

Can I install the vinyl, but select the substrate as ' canvas ', then do the colour calibration? after that, remove vinyl, reinstall the canvas, build a ICC profile for canvas? I want to build a ICC profile for the canvas, without the process of CLC, the ICC is not optional.

The black and white is more warm tone, i need do the colour calibration for this canvas, most of my jobs is on canvas. I put a new roll of canvas, the small black bars seem be ok now, not much bleeding. put on take up reel, colour calibration still failed.

I replace the MK-C printheads, I can do colour calibration on vinyl which is used for printhead alignment. the small Black bars are not bleeding. However, colour calibration on Canvas material still failed. the small Black bars are still bleeding. Why does it happen? there is no bleeding on the...

yes, the seller say it is for latex or solvent ink. and this material is being used without problem on my L570.

Try to created a new material-Solvent Canvas, mode 16pass 90%ink 110degree, 40% optimizer. I try to do colour calibration, but it failed many times when it scanned the yellow colour chart. New optimizer printhead. Pass printheads alignment with self-adhere vinyl. Same meterial, same setting...

system load 1%, new error: 12.2:10 Print Mech: 24V to Verdian Failure, then around 29%, error: 01.12:10 Curing Control PCA Failure. I think the good PrintMech is not working now. No more good working parts :(

The HP Latex 360 with 3L ink supply stops working. It shows error 03:10 when it powers on. the blue and the amber light on the PSU is on. After I switch the PSU from a working L360, It shows another error 12.21:10. Print Mech: 24V to Veridian Open Circuit, then another error 01.12:10. When I...

how to open the cover to clean it? I didn't figure out when i replace the trailing cable last time.

There is the issue of dark/pure color canvas print from L570. The position of uneven print is specific, 2 -3 places, vertical along with the print. I though it was the issue of canvas itself, but this issue happened lessly on L360. I have to spray the varnish liquid to cover the issue...

my canvas print is 1/8 inch short in vertical after i change to a thinner canvas substrate. It happens on L570 and L360. I tried to put on take up reel, still short of 1/8inch.

the random lines are gone, printer works fine now. This is my first time to disassemble latex 570, quite different from designjet z3200. Now i have two metal parts left, don't know where they should be. and the beacon shows steady red light. do i need to reset anything to make it normal...

trailing cable broke here and there. waiting for part. thanks! great help.

Thanks a lot! i will check it tonight.

I replaced the expired ink, all new printers, The printer will still automatically cancel the printing then random lines / strips. i only open the cover, there is no visible damage around cable connection. However paper jam did happen a few times, i found a small plastic part falling off, not...