Search results

Everything is lubricated. Bearings have been checked. Screws on the rail have been checked for torque to see if they are all tight enough. Belt has no faults. Encoder strip has been checked. They are in the process of checking for a workaround on the pulley system.

What was changed was on the actual global config file on thread 3. 110000 to 90000

Im based in Europe. We are running a 2512 with 4CMYK + 1W. Our tech support is trying their best to resolve the issue but its still extremely valuable downtime for us and im here trying to speed up the process of getting this issue fixed.

All the mechanics have apparently been checked. Whether it could be board problem or not, I dont know. We havent gotten there yet. The speed was reduced from 110000 to 90000 to check and it was still an issue. Thankx for the other notes though artbot. I will look into it.

Wish it were that simple. Im working on 4 different substrates at once. (dont ask) Each and every one has the same issue. And always on the same spot. The table has been tested to see if it is warped and it isnt.

Good Morning guys. Wondering if anyone knows how to eliminate this. I have some Vertical Banding happening on my FLORA. Im printing at 1200x1200 with 2 Extracts Bidirectional but any other combination I use gives me the same results. The banding is always present on the same areas no matter...

I would go along the lines of starting a different brand but under the same roof. The "a division of Wraps Ink" route is the best option you have right now IMHO. Use it mainly for advertising purposes but billing would be Wraps Ink. Saves you on legal and accounting hassles. Just mark them off...

Have no idea. Try switching everything off and unplugging. Wait a few minutes and plug everything back in and restart It might just work. Machines have bad days too. If not... well, sorry but I have no other idea off the top of my head

+1

Power source has been checked. Our whole Electric network was refurbished because of our CNCs and there arent any large companies draining any power or causing any spikes around here. Techs have been here more often than not costing us easily into the thousands. Not once were they able to find...

Problem went on to losing all negative pressure even though all the values were in range. Pumps blowing out, PCB losing its firmware or burning out, Water pumps blowing out. Ballast burning out. A full assesment was performed and they said all values were within the normal range and most of the...

They fluctuate quite a bit. Toshiba CA4 Nevermind though. Weve solved the problem. Out with the old and in with the new

Ive also done installs similar to this. not quite as high either but probably a little more risky. try standing on nothing but a pallet raised with a crane to shoot an aerial photograph of a 10.000sqm warehouse. Never... Again....

Welcome neighbour. Portugal here. Any help give me a shout

Welcome from Portugal

Makes 2 of us. I used to call myself a graphic designer but now I say graphic design is just something I do among many things. I could at best refer myself to a professional counterfeiter or say I reverse engineer art and try my best to make it better. Gets people all doe eyed, surprised and...

I have to admit that Im out of ideas. As I said, I havent worked on this particular machine yet. FatCat might be able to guide you through a few troubleshooting procedures if he has the time I guess. I hope you can solve your problem asap. I think we've all been down this road at least a half...

Firstly, replace the filters. You will have to eventually do that even if its to help with printhead lifespan. I make sure all my filters are replaced at least every trimester. We spend about 7$ each so it is quite hefty but it does save you alot of work and is good general maintenance for any...

Many reasons for Ink Starvation. Was there air in the lines when you pulled on the ink? Are your heads clean? Try flushing them out with some solution and retry a test print. What about any obstructions from ink feed to heads? I usually add about 3 ml of flush in a Line with 2 fittings and...

Ive had headache after headache with this T1000. White heads were'nt firing, boards were shorting out. You name it. What could have happened to it did. After clearing out all the lines, replacing boards, cleaning the heads practically back to pristine condition, replacing pumps and valves...