Search results

Didn't get any replys over the weekend... Bump

I've gotten it to cut but when I send a larger job it just stops part way through because it's not using the signlab spooler. Any suggestions? Thanks, T

I've got it set up to cut to TCPIP raw and it was cutting a job, lots of 1.5" letters, 55"x49" and it just stopped right in the middle of the cut file. Can't figure it out.

I'm trying to just cut on my roland versacam SP-540V, It was cutting fine with and then suddenly stopped. There must be some setting that I have over looked. Does anybody have any advice? Thanks, T

I'm looking to use our SV-540V to print onto glossy Cardstock. I was looking on roland DGA for a media profile but can't seem to find anything but paper no cardstock. Has anybody found a profile that will work for this? Cheers, T

I can access the network via wireless no problem. The guy on the phone said that I might want to uninstall the wireless netwrok card and setup the printer to work, then install the wireless network card for the office network. Though this shouldn't matter I wouldn't think if all my settings are...

Well I've had them on the same range. Printer set to - 192.168.002.100 Nforce network Card set to - 192.168.200.202 Is this close enough range? I'm not getting this range deal....and the guy on the phone yesterday was no help.

Right now the network submask is 255.255.255.0 I've got the printer setup as 192.168.200.200 And the Wired card to the computer 192.168.200.202 The wireless card that goes to the office network is 192.168.0.110 and it's subnet is 255.255.255.0 None of the other computers on the network share...

I did just run through it all. I have tryed assigning probably 10 different IP's to the printer and too the network card that has the cross over cable going to the printer. Nothing seems to work. InterCon net tool can see the printer and change the IP, I've configured my zone alarm fire wall...

Well I have installed Intercon Net tool. And even when I seem to be able to get this to recignize the printer, versaworks still wont connect to it. There seems to be a subnet conflict or an IP conflict but I can't find it because none of the other computers share the same IP. I have tryed...

Was on the phone yesterday for 4 hours with our tech guys. They could not figure out the problem, I've tryed hooking the printer up via xover cable direct to the computer and tryed hooking it up into the network switch with a regular network cable. If anybody is familiar with versaworks and...

Hi guys, we've just got our digital printer. Works great! Though we have a wireless card connection for the business network and a wired card going to the printer. The printer is hooked up using a xover cable. I've got all the firewalls set up to allow the new computer. I have internet and...

Wasn't too sure if 500w power supply would be enough.

New system that I would like a proof before I order. ASUS M2N-E ATX AM2 Nforce 570 Ultra PCI-E16 PCI-E4 2PCI-E1 3PCI SATA RAID Sound GBLAN Corsair XMS2 TWIN2X2048-6400C4 2GB 2X1GB PC2-6400 DDR2-800 CL 4-4-4-12 240PIN Dual Channel - x2 Antec Sonata III Black ATX 16IN Mid Tower Quiet Case...

Well i managed to get it installed into windows and then it showed up in signlab as a ttf from the windows folder!! SAWEEET Thanks!

I already have the layout as a cdl signlab file, which wont import into any other program. So I can't convert this to curves.

I have a huge job that was done a number of years ago for a client that uses the font myriad-roman which is a pfb font. Somehow the font is now missing from my signlab and thus I can't seem to open the file. I've done a search on the system for myriad-roman, no luck. Did a search on the net and...

Well those systems seem like the best you can buy! Though I wouldn't need that much power just yet. Perhaps in the future I'll be in contact with you. We need something that will get us by. We need the computer to be networked and accessable for 2 or 3 other design stations (cut vinyl within...

So the scratch disk is another separate hard drive just for working within photoshop?

I'm managed to get a decent system together for under 1400 bucks to the door. It includes a Phenom x4 9850 4gig of DDR2-800 on a Nforce 570 mobo with a radeon HD 3850 512mb gfx card. Would this be able to handle RIP and Printing and still have the other 2or3 users connected on the network to...