Search results

Okay, so i replaced the lamps (like i always do). Everything went fine. When i hit remote to turn the lamps on, i got a error msg. 706 Error UV1 Interlock I've unpluged and plugged back in the power cables that run the lamps. I've taken out and put back in the lamps. I really don't know...

Hopefully someone can help me out. I had a pretty bad head jam/strike yesterday. The vinyl we were using half way through the material they had taped 2 sheets of vinyal together. When the 33 got to that area, I assume (since i stepped out of the printer room) that the heat lifted up the vinyl...

I need some suggestions here. I changed the Cyan head on our JF 1631. Everything went well (putting in the head). I went to run a hard clean to fill up the head and i noticed that the damper didn't compress. I checked the alignment. Clean again....same issue. I then replaced the...

Long story short, our JV3 wasn't used for over a month (operator was fired). Everything worked perfectly fine before. We just had a minor issue with one of the Yellows not reading that a ink cartridge was in. Anyways, Last week when i ran a test draw, only half of the Cyan printed. Nothing...

Where to start..... I changed out a head and when i powered everything back up, i burnt one of the ribbon cables (from the mengta head i replaced). I replaced that and got the error message; System Halt (1) 11d: PCB SLRLY_F1 Figured out it was one of the fuses on the PCB Station. We...

Does anyone know where to order one of these? It's the cable the goes from the head (where the grounding wire screws into) to the board? One of my cables shorted out.

Anyone know where the cheapest ones to get? I saw on digiprint supplies they were pretty expensive. Wondering if that's the standard. We've purchased them before, but they didn't seem that expensive.

Hello everyone. I have a few questions. My Cyan print head doesn't seem to be sucking any ink through. Mind you it was working perfect yesterday. I'll write down what's transpired the past few days. I started off changing the light cyan print head. Installed it and took me forever...

Does anyone here know how to replace/remove one? If so, do you have a video or paperwork that shows how? Thank you.

Does anyone have the manuals on how to replace the cap station and print head? Thanks!

We've had the 33 for about 3 years now. Never had any issues at all. Yesterday, there was a media jam (Oracle 651 vinyl). Since then, the test draw shows that the Magenta (on the left side) is missing most of the nozzles. The top and bottom 1/3's are missing. Only a little bit in the...

We run 6 color inks (CMYKmcWW). Missing the Light Cyan. So, I changed my first ever print head. After it was installed, the test draw looked great. I did all the adjustments (angle adj and back-forward adj). Finished up with those and the test draw was perfect. I finished up real last in...

Ok, so i'm installing my first printhead for the JF 1631. I currently at the Head ID part. I just don't know what numbers i enter into the voltage part. The box i received with the new head has 4 lines. They read; Driving Waveform (AL): AL3 Driving Voltage for 3-15 drop (V): 25.6...

So, i replaced my yellow print head a few weeks ago. Lately we've had certain print job have the yellow ink printing before the rest of the ink. I assume when i replaced the head, i must not have installed it correctly?? It was pretty straight forward. Any help on how to fix this?

Anyone know the proper water temp for the JF's? What each head should be at and what the water tank should too?

Was wondering if anyone knows if you can buy the key pad? Ours is starting to wear though and i just don't want it to short out or shock anyone. Thanks.

I know the manual says "Water pump timeout"....but how do you fix this? Our operator has to shut it off and turn it back on a few times for it to stop. Is there something i can do to prevent this from happening every day? Thanks for your help everyone!

New here....I've already posted a few threads in the Mimaki section. We currently have a JF 1631 and 1610 for flatbed printers. We also have one JV33 and two JV3's. Anyways, thanks for the reading and hope to learn more about those machines!!

How do you check to see if the dampers are properly working? In my test draw, the light magenta is missing about 10 rows of nozzles on the top third of the test. I soaked the head overnight in cleaning solution and did a test and it looked a little better, but then i did a hard clean and it...

Somehow it was switched to auto clean after every run. I'd like to change it back but do not know how and can't find out anywhere in the manual how to do change it. Suggestions? Thanks!