Search results

Se per motore di scansione intendi il motore che aziona la cinghia del carrello, la sua durata massima dichiarata è di 2.500 ore, e a mio parere sono davvero poche, visto che stampare 5 ore al giorno equivale a circa 500 giorni, nemmeno 2 anni. Tuttavia, quando arriva il momento, il motore si...

Tra qualche anno dirai la stessa cosa della Mimaki che hai appena comprato.

Buongiorno, vorrei risolvere il seguente problema che affligge da tempo la mia stampante multifunzione DesignJet T2300. Voglio sottolineare subito che succede occasionalmente. Si possono ottenere diverse stampe perfette e poi questo problema di sovrapposizione o allungamento della stampa inizia...

Si possono ricavare alcuni dollari (Euro) dalle scatole delle cartucce e forse anche dalla testina di stampa, ma bisogna assicurarsi che non ci siano aghi rotti e non funzionanti, altrimenti il valore della testina è pari a zero.

Since last year, if you update the firmware of the SUMMA DC it is no longer necessary to use new chips but you can also install old ones and use tapes from other suppliers.

It is recommended to remove the magnetic prints at least a couple of times a week otherwise they can cause problems. How long were they mounted on the vehicle? and how long were they not removed?

Hi everyone, I have had an HP Pagewide Pro 352DW A4 for several years and I am quite satisfied with it. I have always had little faith in this technology because if there are any clogged nozzles, printing is compromised and there is no way around the problem, which with a traditional printer is...

I can finally send photos of my new silent block wheel and suspension kit for my DC3. For those who need it they have been completely redone. Complete kit price 250 Euro The one on the top left is still the old one. ;)

In un altro post qui sul forum, c'è una persona che li ha tagliati con la CO2. Sto cercando di crearli in un'azienda che ricostruisce la gomma. Ma ci sono due ruote smussate e due ruote rotonde.

They broke for me too and now I have to change them, but they cost a lot. If you have noticed, two are complete round (code 420-025 price 70 Euro/each) and two are beveled (code 420-024 price 155 Euro/each). So I wanted to have them rebuilt by a company that produces rubber. There will be a...

Hi, since I had found a way to use the GSX inks of the Epson SureColor S70600 on my S80600L I wanted to know if anyone could tell me the difference between the GSX inks and the GS3 inks that my EPSON S80600L uses? I find ink for S70600 at a really low price 30 Euro 700ml from a supplier...

Thank you very kindly for your sharing. Can you tell me if manual service for S80600 is also available?

If you can't find the piece, it's easier to reconstruct it by 3D printing. The piece doesn't even seem that complex to draw. I'll take this opportunity, since you have the laminator, to ask you the diameter of the tube where the steel wire spiral is wound and also the diameter of the wire!! 0.3...

I have been using the DAIGE EZ GLIDE for many years (I am in Italy and purchased it from AMERICA in 2013). It does its job well especially on banners. Now I'm building a 64" one as mine is 36" and too small. Cleaning is a bit laborious if you only have to cover a few metres.

If you could send me a photo of the broken piece I would be really grateful. I have the option to recreate it with 3D printing as well just in case. Do you think it's screwed into the hole and the white piece you see in the photo is what's left?

Today I opened the SUMMA DC-3 and removed the right cover and found the 2 sensors, but I didn't understand how they could work. Then looking closer I saw that probably a piece is missing. In the part circled in red of the photo, there was certainly a long pin, which by rotating was going to...

The pinch rollers are lowered because then when the fatal error appears and I have to turn off the machine, the material is slightly blocked by the pinchroller that press on the material. Where do the sensors say where are they located? Note: before this problem happened I heard a very small...

Thanks for your answer The paper gripping clamps work, because they go down and also make classic noise. For the sensors can you tell me which ones? If you mean the two photocells, those also work, because when I insert the sheet the clamps lower. The initial message seems to be, UPPER...

Hi, since yesterday during the start-up phase my SUMMA DC-3, during the initial check-in, the error of the attached images appears on the screen. Can you kindly tell me what it depends on and what we can control. If it is switched on without material, only the message "CAM SWITCHES STATUS ...."...