Search results

That's it! Thank you!!!!! And of course - I do have it, too many fonts to sort through!

Can't figure this one out for the life of me - and I feel like I have it! Any ideas?? Thank you!!

Sounds great - thanks guys. So when the job stops and beeps - just install the ones that are empty and it will resume the job where it left off? I have a cyan and yellow cartridge that are both about 1/3 full and were taken out the last time I replaced all 4 - are those 1/3 full cartridges ok...

Roland 300 - have always inserted 4 brand new inks and always have used official Roland ink. I have been printing more black and magenta my last two rounds - which has subsequently left me with partially used cyan and yellow. Can I continue to leave the cyan and yellow and insert a new black...

Thanks you guys! Would there be negative effects on my printer if there was no A/C in the summer and no heat in the winter and it running in my garage? Thanks again!

Hello - we are moving to a new house in a few weeks and have a few questions in regard to placement of my printer (Roland VersaCamm) and Laminator. The office space in our new house is located in the basement - finished room. My equipment, table, computer desk, etc. would all fit, however I...

I currently cut the allocated sheet size of laminate (and narrow it an inch or two compared to the media to avoid this problem). However - I would love to leave the 30" roll of laminate fixated on the laminator and be able to run my 24-28" wide prints without using craft paper. With that being...

So I have laminate roll width of 30" - but my media width is 28" - therefore centered I have 1" of laminate on the outside of the media which would cause it to stick to the laminator. Is there any solution (besides using kraft paper) to install on the side of laminator to prevent the lam from...

Thank you oksigns - I appreciate it! And jfiscus thank you - I sent you an email. Thanks everyone I appreciate you taking the time to respond. Just trying to get better!

Thank you - yea his example is awesome, but I for sure don't need that much detail. For working with Illy and Photoshop for years, I do not have much experience with the Pen tool and it is annoying just to figure out how to close a path. In addition, when I make a series of anchor points it...

Thank you for the response - and awesome job on your example! Which tools do you recommend using to draw - just the simple pen or pencil tool? One over the other?? Any specific process you would adhere to? Thank you!

Hello - I have a picture of one of my cars that I would like to draw to create the effect of the blue car on the right. I want each panel to be editable (hence maintaining vector properties). What is the best way to achieve this? I do have a trackpad to draw - opposed to a mouse. But any...

Instead of a swatch to fill the layer - I now tried a Clipping Mask - and STILL the vector components of the design show up OUTSIDE the template boundaries. Going crazy. I still put the cutcontour on top of the file and saved as an .eps and imported into Versaworks - and there are no red...

Hello - I am working on a sled wrap for my daughters snowmobile. I have the template, made the design as a swatch and have it positioned exactly where I want it. I have a second layer for the cutcontour and all is well. I go to group the first layer (template), then Flatten Transparency - but...

Roland VersaCamm. Looking to print on Polyester Fabric (the tops of the pop up canopy's you use outside). Not looking to print the whole canopy - just the 10" tall or so front portion on all 4 sides. Any info if this is possible or how to achieve this? Thank you!

A pic of the laminator is attached - he said it works great, has foot controller, etc. Is this the same "Titan" from GBC? Thanks!

Can get a 48" wide Titan 110 laminator for $700 in good condition. Good deal?? Thanks! Using a 30" Roland Versacamm for printing but looking to update from a manual laminator to a electric.

Thanks!

I will upload a test print pic tomorrow - thank you for your time I appreciate it.

Yes I do - remove both covers, use swabs, etc. Just completed a few hours ago and so far so good. Thanks.