Search results

I have a roll of scotch matte clear tape (magic tape) on the cutter and if I run into the issue I just cover the reg marks with it. It always works.

I have chased a very similar issue. I replaced dampers, cap-top from a 3rd party supplier. I still had intermittent ink starvation issues. Ink was not drawing through the dampers consistently. One yellow bank in particular would go away when I printed large areas of yellow. I had replaced the...

No proof without money down...Period

I have a couple of seasoned hs football coaches we do helmet decals for every year with convex. Theyswear the hold up better than anything they have ever used.

Arlon 8000....

I went down this road a couple of years ago and the 4900/AccuRip is the way to go. I actually got wasatch softrip and AccuRip and prefer AccuRip. I use Accuink with Ulano pigment inkjet film on a 4880. Dark blacks and great halftones.

I was of the opinion that it didn't matter until a couple of weeks ago. We had wrapped a van about 18 months ago and one of the panels got printed incorrectly. We only noticed towards the end of the install so we reprinted it and laminated it within 1/2 hour of printing it. I had that same van...

Sure sounds like a cap top issue... Stretch the spring that sits below the cap top to make sure it is applying a good upward pressure. Check very closely for any flatspots on the cap top (As mentioned before I had a new one that was defective). Make sure the alignment is good and that when...

I have been having a similar problem. It started out mainly with yellow. After changing cap top, dampers and damper connectors I had a similar issue just a little more erratic (Cyan and black would occasional drop). It turned out to be a defective new cap top. There was a slight flat spot on...

I had the same issue in Dallas.. I had to buy the 25 yard kits .

Its a pia.. Low energy plastic is not ideal for wrapping. It works but will not hold up. It's like using intermediate vinyl for vehicle graphics. We do 90% coverage kits for side x sides using convex or substance. If you don't have a template it may not be worth your while.

Got 2 and bang for buck you can't beat them... They are no seal but at 1/5 the price they are no daige...either.

I have an issue sometimes with loading 3751 and on occasion have to use the sled attachment HP provides. The vinyl rolls up on the rollers and gets jammed. I sometimes can't get it through even with the blue lever up.

WRX looks awesome... I have an 04 sitting in the corner of the shop gathering dust. I have barely used it in 4+ years. I did rent it to the NBC show "Chase" (now canceled) where it was a confiscated drug dealer's car. Jessie Metcalf drove it in the show. See the pic, the blue wrx in the...

I just traded a 2010 mazdaspeed 3 and I agree. Lots of fun to thrash and 30+ mpg on the hwy. Crazy torque steer though...

Just shy of 10K sqft. I just recently moved from a 100' x 100' to a 60' x 160'. The new facility is setup much better. The first 70' is showroom and production. The rear is a combination of heavy production(CNC, welding etc) and bays. Front and rear are individually climate controlled which is...

Update to my issue which is the same thing. I replaced top connectors, o ring, and dampers on both yellow lines. I ran a couple of cleanings and no ink pulled into the dampers. I switched open the valves and pulled ink through the head with a syringe. It did a couple of test draws fine and...

$18 for one and $1800 for a hundred. Will you screen one? and $18 each for 100 would make you rich overnight if you can get it :smile:

Did you use inksoft? I have been trying to decide if it is worthwhile. We get a lot of folks that design something online and then bring it in and want us to duplicate it. Good luck, it would be good to hear feedback.

This looks cool....