Search results

Has anyone know how to do #Adjust/Capping? If you do, are there any risks involved doing it? Tubelite tech suggested that that's what I should try to do to align the capping station.

I have a roll of "Braper" from fellers i used about couple of feet of it at the start up and than I pushed the media thru. I use Braper on smaller media as well. My media was 54" and the Lam roll was also 54" as well, so I didn't use anything else after the couple of feet.

it is royal sovereign 1400C

Whole 150' took me less than 20 min to finish. The laminator is really design to do this type of runs as well. The machine has media roll tension, as well as lamination roll tension adjustments and take up reel. Because of these three it really made it a lot easier to do this long of a run. But...

Yeah I found out today that I need to upgrade my firmware as well. I am currently at 1.60.2. Do not laugh:) I bought my printer used and installed it about a month and a half ago.

Well, I can say I digested the Elephant today. lol. We finished the lamination with success I wanted to let ya'll know. Thanks for all the inputs.

Well, I change the capping station today which was pretty straight forward, but nothing changed. Before I changed the capping station I test the old capping station with syringe and right side was leaking air but left side was pretty tight. I tested after the change both sides were leaking. ( I...

I was going to syringe it underneath to test the seal whether I need to change the capping station or not, not to draw ink. But it is a very good tip because I did not know I supposed to open the valves first. Thank you very much.

On test draw no magenta at all. Other colors look perfect. I was on the phone with Advantage Signs Supply tech and he suggested that I need to be changing the capping station and as well as the pump and is sending me the syringe to test what you are referring which is hard suction below the...

Dampers full of ink as far as I can tell. It seems like there are no leaks but I do not know how to check it properly to make sure. Can you offer any tips?

I am asking this just beacuse I don't know but logically thinking, if there was some air in the line do you think 3 fill ink would pushed the air out?

Funny you asked that while it was printing it beeped and I checked what it was and the red light on Mag cart #1 was on but ink level was 29% so I pushed the cart in and it turned in green however the 2nd Mag cart was 98%. After wards I did 3 time ink fill but still no luck

Hello everyone, :omg2: While it is printing banners on my JV33 magenta stop printing. Right before this job I printed 300' digital vinyl with no problems what so ever. I switched to print this banner job and in few feet in to the job magenta stop firing. Do you think the head is clogged? I...

I made I gigantic circle and unwind it from it's core and after 24hrs I wind it to it's core.

Hello everyone, To individuals who are interested creating variable QR Barcodes, we have a capability create them from your .CSV file. Pretty much any information can be QR Barcode. Let me know if you have any questions.

Let me ask a question. I just printed 46' trailer work which is 54" x 150' roll if I was to have what you have could I start laminating it as soon as it finished printing?

Hello everyone, My very first 46' trailer graphic wrap it its all printed and I'm ready to laminate the 150' roll. But I need some tips. Being so wide 54" and so long, what its the best way to feed it so it does go strait as arrow. I'm little sceptical doing this without any pointers from...

I have been demoing Production House with vista. So far i have not encounter any problems as far as OS goes.

I took little bit of everyone's advice. I ran it on 6 pass mode 540x1080 it run immaculate after adjusting the media setting of course. Because of ya'll's help now I have better understanding of the JV33 functionalities. :U Rock:

Hi ya'll, I am trying to pick ya'll's brains little bit. The artwork is nothing but a solid piece of color which is PMS 2617 and the dimension of it is going to be 42"x96". Earlier last week I did a small swatch print (3"x7") to my customer and it appeared to that there was a little banding...