Search results

The reseller I’ve been speaking to is not sure. They seem to think the Rip may have issues dealing with the set sizes of material the machine can cut. Can anyone confirm 100%? Thanks.

Hi, Question as per the thread title really. Does anyone use Caldera to create the reg marks for the SumaCut D140FX? Are the 2 compatible? Thanks in advance.

Thanks. I think I might go for it. I think they must have Ethernet now... https://www.psw.co.uk/d140rlfx-2e-suh-001511-summacut-r-d140fx-cutter-with-lan-1400mm EU brochure states Ethernet and USB... https://www.summa.eu/pdf/products/Rollcutter/LowRes/Summa-Rollcutter-Brochure-en-LowRes.pdf

As well as using the right laminate you also need to make sure that your ink adhesion is very good. If not and a corner / edge of the laminate starts to lift it can take the ink off the substrate in one great big piece while still stuck to the laminate like a carrier paper.

Thanks for the info. Are they the only differences? If so, I must admit to being tempted as it’s 30% cheaper than the non FX version here. The model I’m looking at is listed as “SummaCut R D140FX Cutter (with LAN)” so I assume it includes a network port? It would be used almost exclusively for...

Hi, Thinking about getting a SumaCut D140FX. This would be our first vinyl cutter as we’ve been print only until this point. Can anyone help us with the following please?... How does the FX model differ to the non FX model? What are we not going to be able to do with it that we could with the...

OK thanks. Do you know what the official minimum size that HP state is? Or know where I can find it? Also, how do I trick the machine to do an 8 x 10? Thanks.

Hi, Can anyone tell me what the minimum panel size that can be printed on this machine is please? I can't seem to find it in the literature. Thanks.

Thanks. Also, how do I clean / where do I locate the encoder reader and the home flag sensor? Are there any instructions online anywhere? Thanks again.

Thanks guys, we’ve left it on. Am I right in thinking that if the printer is switched off but still plugged in, it still uses the mains power to maintain the vacuum in the heads? Or does it switch to the UPS? Thanks.

Thanks, yes I’ve cleaned the encoder strip with no luck. I think it’s definitely an engineer job. So is the consensus to leave it on? Anyone else? Thanks.

Hi, We have a HP FB750 which comes up with the message “Encoder strip error” with the option to restart or retry. Choosing either option gets us back to the same error message. Our support company has gone home for the night and we’re not sure if we should turn the printer off overnight or...

Hi, We've had a FB750 for coming up to 2 years now and recently we're getting issues with inconsistent colour. Essentially we can print multiple copies of the same artwork using the same blue colour and they'll all come out slightly different shades of blue. The lamps were past their best so...

Hi, We have a FB750 which has come up with an error message saying the waste ink container is full (image attached). Note this isn't the normal maintenance message where it's asking you to turn the spigot to empty the waste but instead talks about the float being disconnected? If I try and...

Interested. Particularly about the F2630.

Hi, We want to direct print on some marine ply with our FB750. Does anyone have any tips on what we should paint / varnish the marine ply with to give the ink the best chance and also give us a nice white base to print on? Thanks.

Thanks for the reply. PM sent. What was the intended use of the laser? Acrylic, fabric etc? Was the laser actually working? Thanks.

If so, did anyone swing by the Zund stand and notice if they were showing a new laser head attachment and more powerful router for the G3 / S3? I've heard rumours of this but can't find any pictures, info, press releases, anything. Did anyone visit the Zund stand and notice? Thanks.

Thanks for the reply but as explained the sleeve that comes with the post is only 24" long. Is there any point having a hole twice as deep as the sleeve? As it would mean the sleeve would just be sat at the top of the hole with 24" of concrete below it. Taking that into account, would it not be...

[FONT=Verdana] Thanks for the reply. Yes that's the plan... Concrete the sleeve in then insert pole into sleeve. Regarding your measurements do you mean make the hole 18" deep or 18" wide? Thanks.