head

So i just fully replaced the second head of the CJV300 and connected all the tubes properly from 1-8, they all filled up and worked perfectly fine when I tested them with a test print no issues! But for some reason one of the blacks doesn't work and it doesn't fill up no matter how much I tried...

I just finished replacing the head and dampers, did the proper cleanings to charge the head. Went to do a test print and the warning popped up. I went and turned off the printer (main switch) waited a minute and tried again with no luck. Went into service mode the thermistor is reading 24...

Need some help chasing an printing issues please!! - Before pic is what it was printing and after is what it’s now printing - Mimaki CJV300-160 I’ve changed capping station and dampers in both heads, I did an machine ink fill and nothing really happened, I opened all the cartridge valves in...

We have a JFX200-2513. Recently the movement of the head started to get very loud. It seems like the head is having trouble or added resistance moving. I am thinking that the slide units on the linear rails are starting to go bad. I see that they have grease zerks on them, but they have a...

I need a printhead for a Mimaki JV33-130. Prices online range from $765.00 to a bit over $2,000, which is a huge difference. Most sites list the printheads for $2,000 +(-). Is there a difference between the mid seven hundred dollar heads, and those that sell for two grand? Here's the link to...

Hi guys and gals. This is my first post, i was searching for info on google about a problem i'm having with the cutting head of a d60r and found this forum. The problem is that the blade is not moving down as soon as the vinyl starts to move so the blade is not cutting from the beggining of the...

I bet that headline catches some attention ;) More to the point.: I just did an experiment with a DX4 head. Disassembled it by removing manifold and rubber seals, then basted the unit in Acetone as I was curious if parts would melt. Used small brush to clean circuit board and surroundings...

In a nutshell, we moved and printers had to sit for a bit, thus having issues with some clogs. Need help in doing a head-soak - DX4 solvent type. I know and have done the procedure of clamping and such, just haven't in a very long time and can't recall how to get the heads out of the way and...

Hello all, I come to you, again, for help. I have been fighting with our Mutoh for two weeks. Friday, Jan 31, It printed fine. The following Monday, Feb 3, it showed a lot of missing segments on the nozzle check. I alternated between cleaning cycles and nozzle checks until I decided that it was...

Ugg. Like a dummy, I was moving the dampers around and I heard the sound you never want to hear (CRACK), and the damper on my BRAND NEW black DX4 printhead went loose. I quickly found out that I had snapped the plastic nipple off inside the damper! So in a panic, I grabbed one of the old...

Hi! I've just changed printer heads and all is good, but now I need help with BIAS adjustment, etc. I have a service manual for a SP300, but it's a bit different to the SP540i. Anyone have a PDF link, please? Thanks, Ian

Hi. I´m new here and hope to get some help. I got myself a Mutoh VJ-628 from an old client/competitor. First the machine didn´t print anything and then after couple of tries when the machine was powered on head only moved for couple of sentimeters(1-2 cm). Can someone give pointers where to...

These are photos of a head from a Mutoh VJ-1324XS that wasn’t printing well on some channels. I quickly saw the ribbon was torn on BOTH sides! I’m surprised that it still prints anything. (How do these ribbons usually get torn?) I didn’t remove the head off the manifold to see if the ribbon...

Hello everyone and happy 4th! I just replaced all four dampers in my 1624x as well as my maintenance station. When I go to turn the machine on it acts like it’s going to fire up but as soon as it reaches the “version 3.0” screen it shuts down completely. Does anyone know what is causing this to...

1.i have a Roland sol-jet pro4 xf-640i with 2 head(8 color,and i want to change the configuration to single head Any idea how to do this? we check in service mode i didn't found the option 2.DX7.head how much price & details ( we fond some online market different price ,1 sight 640 USD.2...

Certain colors are not being printed correctly and it seems to me thats it got to do with the yellow. The test print looks fine but when I printed a color chart i've noticed that all colors that have yellow in them are noisy as compared to those without yellow are solid. Does this mean that one...

Hello, we have a ecosolvent printer Oce CS 9160 and we are thinking of buying a new printhead. The problem is that when I looked online for a oce CS9160 printhead, I can't find one ! When the machine starts, it says MUTOH Valuejet 1614, so I suppose the head is DX5 (at least it looks like). I...

Hi everyone, Happy New years eve! As I head into 2017 I wanted to give my printer a cleaning since the blue and black print heads were deflecting a little. So I went a head and put in a cleaning cartridge and drew the cleaning solution through the blue/black print head with a syringe. I...

So I made a huge mistake. I went to print a template onto the table and set the head height so it would be 2.1mm away from the table. I forgot to take out the media locating screws and needless to say the screw took out a head. My question is? Shouldn't the safety bar have prevented this? I...

Has anyone ever seen this before? Check out the attached picture. The nozzles are stuck ON. Things that have been done so far. 1. Head verified clean and clog free. 2. Both head cables replaced 3. There are no errors on printer 4. Maintenance Station works great. No leak issues or pump issues...