roland

Anyone have a recommendation on the best place to get different camouflage patterns for printing? I have a customer who wants a boat wrapped in camo but does not like the ones I have. For printing, not camo vinyl. TIA

Hello, I've had a big problem with my BN-20 printer for a few days now, first it all started because I wanted to change the print head damper (because the yellow wasn't coming out anymore), during the 1st reassembly I had a bit of liquid in the print head cable plugs, and when I restarted I had...

Hello, I have an SP300i model, I have been having a problem for the last 1 week. When cutting the media, when it cuts at the beginning, it does not cut completely as seen in the photo, but the cut gets smoother from the beginning to the middle. What do you think could be the cause? Our cutting...

Just wondered if anyone has had much experience in moving a Roland TrueVis Printer? My new TrueVis3 SG540 is arriving at the end of the month (very excited) but I have to get the machine up the stairs onto a small landing and then through the door into my print room. Going to have to lift the...

Hi All, My first test I used 70-micron Vinyl. Using a 60° blade, I have adjusted the blade depth, scored 2 cuts of vinyl layered over each other making sure the top layer cuts through, bottom is scored. The machine pressure is set was set at 45gf. I have adjusted the pressure for normal cuts...

VersaWorks Dual gives ink level remaining in 25% increments. Is there any way to pull a. more accurate reading from the printer? Like from a network command line/web interface? I've used a Canon printer way back when that had an 'ink check' via a web interface -- it was surprisingly precise...

Is this a normal amount of ink in a week's time with very little usage?? Every other time loading material goes through a clean cycle. Driving me nuts with the waste!! And then a slight clean for test print. (I want to see what the test print shows before a slight clean.) Vg640, TR2 ink...

Every morning the test print looks like the attached and after 1 reg clean comes back perfect and prints like a champ. Replaced all captops and had the tech install and made sure it's seating correctly. Fairly new heads. It also used to jump from one channel to the next. Now its only on the...

Hi, I am having trouble with my contour cuts from VersaWorks. It appears the contour cut is slightly off probably because of the Pixels. The contour cut is correct on Flexi. However, when I send it to VersaWorks, it is incorrect. How do I fix this issue?

We have a 2005 Zund M-800CV for sale. This is the Conveyor style so it will cut unlimited length files. Can be configured for any application desired for any cutting material. It has a camera setup available to read crop marks. Asking $15,000 or best offer. Free to come and inspect and take a...

Hello folks I had my original Roland Cutting Plotter, somehow they broke and found this one almost same as mine - https://aliexpress.com/e/_DDxfJ1T Since I dont like to buy on aliexpress before I buy it just want to hear your exp... thanks folks!

Hello! A few days ago I changed my cuter blade, and i noticed that it makes a loud noise when cutting. It doesn't cut through in some places, and i can see that it was cut like this on some - - - - - - - - (if you understand). The cutting blade is from the same package that it came from...

Hi We have a Roland LEC540 running CMYK plus Gloss and White however we do not use the gloss so it gets wasted in the waste tank. Does anyone have any info or guides on swapping the printer to CMYK plus White White as we use white a lot. I have done this process before on a mimaki however there...

Trying to help a friend with his printer, however we cannot get into service mode as the machine keeps booting up on its own when the main power switch is turned on. We're both stumped. See video for visual reference.

Hi all, I’ll admit right off the bat I don’t use it as much as I’d like. I put a new head in at the start of November last year as the other had overspray on black at around 90k shots to a paint it wasn’t useable anymore. I’ve not used it since then but it stays powered on and does it’s periodic...

Hello folks, As the title say I want to buy 60 Degree Carbide Blades compatible with Roland Vinyl Cutter and found this one on the aliexpress - https://aliexpress.com/e/_DFIL2vj Price seems good but I am not sure about qulatiy, any help is wellcome. Thanks!

My printhead needed replacing because of lines in the cyan, according to the service tech last month. I could get away with running on high quality and manually dabbing the head on a manual clean every now and again so i left it. Well today after a manual clean i got absolutely nothing from the...

2021 Roland TrueVis SG2-300 30"roll to roll large format printer for sale. Works great. Regular maintenance preformed. Low hours, still in current use. Can provide video of machine running. Upgrading to 54" printer & do not have the space for them both. Pick up North Florida $5,500 OBO

Hi, We have a lec540 and when we turn the printer off after use it makes a clicking / buzzing noise. The noise seems to be coming from the power unit but I am unsure on if this is normal or not as we have only just purchased it. I can switch the switch or at the back and this stops the noise...

I’m interested in Roland’s new belt drive flatbeds. All the features seem enticing. I like the footprint of the 64” machine with the 7” x hight. Does anyone have any thoughts on this printer? I’m also curious if the gantry could come off. If I were to buy this it’s a few inches too big for my...