Search results

cured = secured. you have cables for the larger falcon outdoor machines which uses two color heads. The junior uses 1 dedicated black and 1 color head. Paco

Head rank will not show up this problem. Is this the machine selftest? Have the head cables running from the head board to the heads have been cured and placed correctly? Paco

OK if it only moves in the middle a little it has nothing to do with the right hand side of the machine like capping and maintenance station. When you replaced the head could it be that you loosened up one screw thath holds the carriage to the metal band? Check if the height lever is moved (left...

Put the head in center of the carriage and then switch the machine on. It should travel tot he right hand side to the cappingstation. Tell us what happens....... further check this link.... http://www.signs101.com/forums/showthread.php?103543-Y-current-error-then&p=1085856#post1085856 Have look...

38" version?

Duane, VMP is cutter software not a printer/RIP software. Do not invest any time the stuff that came with the machine. Look for a used Flexi 8.1 version here at this forum. If in doubt first ask before you spend money anyway. Sell the VMP if you do not have a cutter. BTW the machine has a...

There are various ways to perform a head soak / clean. As the cappingsstaion sponge is already not flat anymore I would take a lint free clotch and soak it in cleaning fluid and place it on the cappingstation. Or clamp the output lines on the cappingstation and fill the cappingstation with...

Good to hear it is working now and letting us know. Like Robert said, a new capping station is the first to take care off when ink cleaning is not correct anymore. During cleaning the pads in the cappingstation need to be soaked with inkt and then drained in th el;ast seqeunce. If that is not...

If I am not mistaken the machine use Lc and Lm and Black in the left head. So the left part of the maintenance looks all black. Clean all around the maintenance station and the head caps with clean fluid. Put a syringe on the left capping part out put and try to suck ink through it. Also check...

If it always happens after the start of a print you would suspect inkflow is not sufficient enough and maybe before that point the mising nozzles are not visible enough until the inkflow is getting less. Problem is you do not know what happens during printing if more nozzles stop to work and...

Maybe I am mistaken but if you miss nozzles you cant print without banding. :-( Your single pass printing (test print of the machine) should be OK otherwise it will never be 100%. Looks like the Magenta is missing nozzles and the the cyan not. Depeding in the number of passes and the position of...

If I am not mistaken I see two white lines in the green. Paco

Do you have a picture of the machine selftest nozzle check? Paco

Go to the menu in the machine material compensation is there to be found. Print a test file and measure the difference for transport and compensate for it. Better to use a large length for better accuracy. Paco

Read this reply. http://www.signs101.com/forums/showthread.php?t=104037 Some basic check up for no ink is placed there. Blown fuse can be also the case. Which outdoor machine is it exactly? Paco

If the sensor fails, short it or replace it with a small switch. This short is same as it see the sensor. When the message on display arrivés that the bottle is full just open and close and reset message on control panel. ALWAYS keep an eye on the waste bottle............ Paco

Open a file and select print and rip. In the rip and print screen go to the Advanced tab. In the option Color mode check that CYMK is choosen. Let us know the result. Paco

Ok that is good news. Let us know the result. Paco

On the panel on the machine left bottom switch says mono/color. In the software I have to check as I am now at work...... :-( Paco

Possible too..........:goodpost: But normally the rip overrules the hardware setting for that and resolution except for paper feed setting.