Search results

I would first start by cleaning the encoder strip and with canned air dust off the sensor too. Use alcohol pads to clean it. Also move your pinch rollers to other areas my machine would work at times when I did this but failed eventually I got a new strip and encoder sensor, put it in and it...

Thanks I'll try it and draw some black ink thru to manually flush it from the damper. But any idea why in my test print you can see the 100% K swatch going cyan when all the other K swatches are nice and gray/black? You can also see it at the end of the white to black gradation strip...

Here are test file prints.

So I have done a head soak to keep my heads from drying up while fixing my machine, SP300V, I noticed in the K/C cap it seemed to have a lot of C ink in it. I got my machine running again and the first nozzle check it seemed like the K nozzle was printing more like C, not a solid black color...

OK SUCCESS! I looked at this video and got it to work some how: AS I did the limit procedure I got to the Cutter Down POS step and the cutter did not unlock...at this step I then pushed the print head/cutter all the way to the right and heard one CLICK locking it there. I then shut the...

Hmmmm...well just put in NEW encoder strip and the encoder board and it does not seem to make a difference. Made sure strip is centered between the encoder board sensors etc...I still get to the step where I have to move my cutter section to the far left but it does no disengage from the print...

Also NOW on machine start up it wants me to hit the POWER button to do a cleaning before the machine even boots all the way up, then it goes into the 0101 error. I then reboot it and try the Limit Initialization without doing the cleaning and it does not unlock the cutter head and I get the...

It's centered....I guess next I will just replace the encoder strip and see if that fixes it...

OK, I just put in a new linear encoder board and have a new strip but not installed yet. I have had the problem of the machine giving me the 0101/Service error and can not complete the Linear Encoder set up so I bought the strip and board. When I just put in the board now it says to do a...

OK, so I got my new parts and went to test the machine one more time before putting them in. Turned it on, and I moved the pinch rollers to s different section, did the Encoder Initialization again. Heads went up to cap properly, came back down and then the head moved to the left slightly off...

I just tried doing it again...I do the Limit Initialization, move the head to the left about 1' and it says to next Move To Cap Position, I them move it back over the caps and hit enter, caps go up and then it says Setting UP The Limit, Processing/Detected, then it goes to Setting UP Cutter Down...

I did the limit position initialization, then it goes to the next step Setting UP Cutter Down POS and it get an unrecoverable limit sensor reading...new sensor needed? It's coming in the mail tomorrow.....

I now also get the 0101 error, looked it up and thinking maybe my encoder is bad or the strip? It gets to the Cut Down POS and then just stops and I have to switch off the machine to get out of the mode/0101 error. I have a new encoder and strip on the way from ebay...think this will solve my...

When I turn on the machine, the cap stand moves down and then I get the 0110 error. This has happened several times in the past and I just power down then back on and it usually works, but now I can't seem to get it past this step. I just read about cleaning the encoder strip, did it with a...

Ok, I use Illustrator and then run my file thru Versaworks, just did a basic boat lettering job and set the black in illustrator to the black swatch, ran my numbers and the black is not a pure solid black like the print/alignment/cut marks the machine printed once I laminate it. Not a head...

Any idea why a lot of the corner cuts/angles don't 'complete' and I get like the tails on a test cut but when I do larger cut paths they are smooth and complete like an oval or circle?

I'm trying to get a good cut off my SP300, the test cut square does not complete the cut, this is running on vinyl and lamination but still same issue with only vinyl. New blade, I adjust the speed down, offset should be .25 and I adjusted it down to but no effect. Do I need to adjust the...

I got two heads I just replaced,email me and I'll text you a pic of them the old ones are clogged, one little nipple for the damper is also busted but other than that I guess you can use them for parts!

I haven't done much cutting on my machine, just did some print/laminate then send it back for cutting. Some of the corners seemed to not have the cut path cut all the way thru...I had pressure about 90 and speed I think 30...was it set to cut too fast? I know I need to give a little more...

Can anyone give me a base setting for my cutter pressure when cutting vehicle graphic media after I laminate it? I use about 85 for unlaminated now and a real slow cut speed.