Search results

About the thick black, you have of course tried another file with only 100% K on the black? Do you have for example MAX Impact set on in Versaworks?

Check if this occurs after you,'ve cut a small sheet or short piece of vinyl. When we get this it is after you've cut a small job on a leftover piece of vinyl and the cutter has sensed that the vinyl is short or just enough for the job it just cut. Then it cuts a straight edge when loading up a...

Best investment I made 2019! Definately suggest you get one, especially if you're allergic!

I hope they are not expecting you to wrap the doors as well? In that case, run! You cannot get the handles and bars off, at least not easily when it's a used container. Also, be prepared to maybe use a high tack vinyl, paints on these are tough to get something to stick to sometimes. I agree a...

Thanks! Yeah, we got one laminator back up running but the 330 seem to need a new power supply so I'm happy it's the end of the day now!

For some people Friday 13th mean bad luck. I didn't think so until today. Morning started off perfectly, in the afternoon we fried two laminators and one Latex 330 due to (probably) a short in one of the power outlets (cables have come loose inside outlet). To top it off the handle on the soap...

Does this happen even if you print the same file on paper or any other material? Just to rule out it has something to do with the cases?

Good idea, we actually talked about making some stickers for putting on packages the other day so that would be easy to do now! Thanks for the tip!

We have branded packaging tape but reuse old quite fresh boxes. The way I see it we save a ton of cardboard going to waste otherwise. I am sure the customers maybe would like the brand new boxes but it's a tradeoff with eco-friendlyness and cost saving. No one has commented the packaging yet...

Thank you AlsEU, very informative! I did the subtank maintenance for LC this morning and did not get the error again. Sorry for dumb question but how do I do the sending adjust procedure? Is it through a software on the RIP PC or on the machine? Never done this either though I probably should...

Do an image quality optimization before printing and print gutters/bars as previously mentioned.

Thanks for the tip ProColorGraphics, I could try to order a new LC cartridge and change. I've not seen the error on ny other channel. I also think the pump might be on its last leg since it sometimes has problems with ink starvation (or so I think) but that seems to get better as you print more...

Hello! Happily printing along today with the Fujifilm LED 1600 hybrid printer and suddently it stops, showing Error 63 f Ink tnk remain, and it seems to be LC that's the issue. The LC has been a bit weak but otherwise nothing out of the ordinary. This happens randomly and causes the print to...

Could be the ink limit, have you tried a canned (downloaded) profile if available for that material?

Sorry to hear about your problems, at first I thought it was temperature issue (too low) but since you've tried adjusting it can't be that. Have you tried to put high heat on and increase the interpass delay (just shooting in the dark) to give it slightly more time to dry. Hope you get it...

If you don't have a complex cut you can of course hand cut it to be sure nothing messes up while cutting to avoid one risk factor.

There might be a reason the other team backed out... If you still are going to do it make sure to check the equipment the customer supplies, check everything including when it last had service, certification, safety equipment etc. etc. The loss of time and/or material will be nothing compared to...

We make some small parts, small batch washers with a hole pattern in them that the customer uses for attaching switches to. We apply a decal over the surface and it looks neat. Customer buys 15-20 pcs. a time and it's printed with ABS on a desktop simple 3D printer, costed around 1500 when I and...

It's difficult to turn down jobs. I started out as a one man show and when we've grown as a company we have to turn down also old customers who pays too little and interferes with profitable work. It's tough when you've been used to be happy about every job coming in but it is neccessary. It is...

What if you select "print as image" in adobe acrobat when trying to print the pdf? Does clipping still occur? https://helpx.adobe.com/acrobat/kb/quick-fix-print-pdf-image.html