Search results

I have an Hp 450c potter. I have a draft medium and fine print setting on the unit, however if I set it up to print fast (draft) it will still print in fine. After I print 4 or more sheets it will go into the draft mode, It will print a few sheets that way than it will go back to normal...

I need some input.. I have an Fj-52 converted to eco solvent printer..I can't seems to get the red to print right...it looks more pink then red. I am using FlexiSignPro. 7.6 I am using RedGiant a third party ink,,,, cleaned the heads, capping lines, drain tubes,, so what next? Thanks,

I do notice that the ink pools quite a bit in the cap top before the pump pulls it down to the waste bottle. I will pull the capping station and clean the clear tubing, which been a while since I cleaned it. Thanks for all your help!

Getting excessive ink splatters around the capping station each time I do a head cleaning.. I see splatter all over the place. I adjusted the print head and that did not fixed the problem. Could it be a bad capping station?

Now that I have all these wonderful information on how to drink it in coffee.. and to still me neighbors cat poop, the next thing I thought you tell me to mix it in with my garden soil it will make the soil nice and black and gives it a top soil look.. May be I will just mix it with the old oil...

Can anyone tell me where or how to dispose my waste ink I been collecting in gallons of jugs?

jhill, I installed new dampers again, also flushed the printhead. It prints just fine the test print..

I am using a third party eco solvent ink ColorBest...I may try switching inks and see what happens..

My CJ-500 stops printing the color magenta during printing proses. I installed a new damper, capping station, it seems the print head still have some life left in it by not showing too much issue in the print test...See attached pictures it was printed just on poster paper an 360 res...at a...

I want to purchase some pre made graphic designs to print on One Way vision vinyl film, it gotta be high res. I am sure it's out there just don't know where to look. Maybe some one here can point me to the right direction...

Thanks for the help guys! Higher resolution took care of it...Thanks again!

Hey guys, I am using FlexiSign-Pro 7.5 to do print and cut on my Roland Cj-500 and getting bad print results when printing text. The edges a bit jagged, I usually create my work in Photoshop and they looks fine until I tried to print them from Flexi...I sure could use some ideas of what to do...

I may have just figured this out....was reading how sometimes static can affect the printer...I was trying to print some stuff on paper and it seems that is when I started to have problem with my printer stopping for no reason during printing process. Well...I put some vinyl in and it printed fine..

CJ 500 starts out printing fine but after a very short while it shuts off..saying Illegal Shutdown, it never had done this before...can anyone help please!!

My Cj 500 stops printing in the middle of printing process....It says Illegal Shutdown.. any ideas of what to do ??

Can anyone tell me where do I go to clear preferences in Flexi 7.6 I just got the program, still new to these. I read it's a good idea to clear preferences tie to time. I am having some printing problem, not sure if it's Flexi or my CJ-500 it stops during printing and just shuts down...

I tried to figure out why my Cj 500 converted printer shuts off in the middle of a printing process, but with my limited understanding of this printer I can't seems to figure out how to fix the problem. About less then a minute into printing the sub power goes off and on the panel window says...

The blue was still ok...I started our printing the black just fine...when I looked the top half of the text was printing out yellow, so I reset the printing and sent it to the printer it started out black ok than again yellow..I cleaned out all the lines, installed new dampers, print heads...

Sounds good...if not broken why fix it".

I am not getting smooth clean text printing in FlexiSign Pro, even at 600dpi.. What settings in Flexi should I be using to get good sharp text printing? Also the other day I needed to print a vinyl sign with black text over light green background, sometime before the print was finished out of...