Search results

Unable to view your images. Have you replaced the encoder strip? When I replaced mine it improved my prints significantly but am not saying this is the fix for your issues. There are a lot more variables. I would replace the cables first also as printhog mentioned.

I think you may have to set your baud rate settings so your pc and cutter can communicate with each other. But I think you're half way there. Check your preference settings in the printer driver, under printers. There should be some settings with x on x off, baud rate etc... These should match...

Hello Paul and welcome! This is one great Forum kudo's to Fred and all members. Will be signing up to your 3D print forum too. Have been 3d printing for a while now, with a background in both cnc and design am always keen to learn and picking at your brain would be knowledge much appreciated...

Back track your steps. Did you replace the black O Ring that connects the tube to the damper? A worn one can cause air to get in. Possibly your new damper could be bad also? I had a new damaged damper in the past. Check your ink line doesn't have a kink. I personally draw ink back from the...

I have the same problem not everytime but on occasions. Moving the pinch roller a few mm either way seems to help. But I know the cable needs to be replaced. Was also thinking that maybe the sensor is dirty, has anyone cleaned this with satisfactory results?

Welcome Davyde

Changed my encoder strip a few months back and this stopped the over spray I was getting too. Also noticed static on certain media that also caused this. Replacing the encoder strip did the trick for me.

That is disappointing to hear. From all of the reviews I've read they are one of the best cutters on the market. I don't own one myself but am planning on getting one. Is there a possibility it may be the printer thats causing this? It is a new cutter and the printer is older. Have you...

Had a similar issue, new blade and jagged edges on vertical lines only. Found out it was the blade that was the problem.

Flanges I believe the thingies are.

+2 Clean the encoder strip. Had severe magenta overspray on mine for a while only at the ends after the print had finished. Heads were clean and no signs of dust, had to replace the encoder strip due to wear, after the set up and calibration the overspray had 95% dissapeared. 95% because I have...

Sometimes lighting plays a role when reading the crop marks. Had read on other post a user had no issues whatsoever then all of a sudden it had difficulty sensing the crop marks. They ended up adjusting the room lighting somehow by reducing the glare that bounces off the substrate that the...

Thank you!

Data / Ribbon Cable Part Number? Hello all, This is an old thread but I can't seem to find the part number for this cable. Would appreciate it if someone can share this info. My SP540V starting to read a 0mm sheet width (twice or three times), in the past week. Moved the left pinch roller a...

The Avery type were great. When the felt on mine eventually wore out, ripped out some double sided tape, cut my own felt material (purchased from the local fabric shop) and now an endless supply. Does the job.

Soldering a couple of wires connected to a fuse holder on top of the blown fuse worked for me. This was my last resort before replacing the board. Fuse holder is easily accessible now and can be replaced at anytime. Just ensure to only do this on the blown fuse.

Hi Darren, Im sorry I can't contribute with any info towards your main board setup. However Im curious as to what was looked at on your shot board that caused the magenta and yellow channel to stop printing. I experienced a similar issue and found that the small fuse for this channel was...

From experience the Roland CX series vinyl cutter drivers are suited for 32bit systems only. My CX 24 still runs on Win XP 32bit and have tried just about everything to get this to work on an updated 64bit pc. It's a pity bcos the cutter is still performing well if only Roland can release...

Have been using a Neolt Trimmer for many years now. It's been a valuable addition to my setup. Takes the pain out of manually cutting labels which I did for some years! http://neoltusa.com/products/manual_rotary_trimmers.php

Thanks... I knew it wasn't a good idea but I kinda like to try things the hard way at times. Luckily it's not all the time!:thankyou: