Search results

Hmmm.. I'm using the same setup with 360/s2 s140t.. Sometimes, i get the same message about bars being wrong, but usually laminate needs to be pushed with finger and the opos reads it better after that. Your cut server automatically now sends cutting lines to folder...

As much as I love my 2 tangential s2 summa cutters, even summa can't cope with bowing effect and cut spot on. I've had l265 with s2 140t / wasatch rip, and now 360 / onyx thrive with same s2 140t cutter. In my opinion, the key to accuracy of cutting is the backing paper of the vinyl. Thicker is...

Yes, download the service manual and do that yourself. We changed the whole ******* carriage 3 times before my old 26500 went to heaven :D (long story, carriage rod worn out) We didn't have any technical support besides that manual and still managed to get away with it. Changing that card is 30...

really? I've changed both of my drag knife cutters to s2120t and s2140t but i have never used the drag knife. I bought those to get rid of drag knife problems :) do you cut very long runs?.. tangential is much slower but i'm too lazy to change to drag knife and adjust the pressure and depth.. :D...

I've had only summas for the last 15 years, and changed both to tangential models. Can't go wrong with Summa s2 T:s . I'm never going back to drag knife.

try to find used summa

I haven't seen 3m envision luster laminate, but would it be something like that.. Atleast normal envision laminate is very, very clear :D

buy the whole carriage and change it by yourself. You can download the service manual from net. We changed 2 carriages and 5 x bushings before the carriage rod was too worn out. New carriage has bushings and felts already installed and costs under 500$. If you go that road, change the belt too...

I bought my first rolls roller at 2009, last year i sold it and bought bigger 4500x1800mm (177x70 inch) CWT. CWT is nicer because there is no upper beam i think. But rollsroller has just released https://www.facebook.com/Roll-X-Flatbed-Applicator-905591046204855/ .. If I heard right, it's...

I've had x or y overflow several times with my older S120D. It was always the motor. Took about 15-20 minutes to change by myself.

+ one for that wtf.. i have 4500x1800mm CWT (6 x 15ft or something near that) You don't need to reach across the table. You can work on other side or have some helpful things like this : http://www.rollsroller.com/our-products/accessories/long-reach-cutter/ ROLLSROLLER LONG REACH CUTTER two...

http://www.rollsroller.com/our-products/accessories/heat-roller/

Heheheh, i bought my first rollsroller at 2009 and my CWT last year.. your feel that youre faster is wrong :D You can control the speed by pushing or pulling faster, and there is no waiting time at moving the roller up and down. Just try it.

http://www.partsnow.com/docs/service-manuals/hp-designjet-l28500-service-manual.pdf not 25500 or 26500 but if you don't have the correct service manual, read that :) (i don't remember from where i got mine but googled that)

I don't believe it is the felts. When the felts go bad the machine ask for carriage rail cleaning and lubricating all the time. Bad felts make friction. I have changed bushings 2-3 times and the whole ******* carriage once but never had problems like you are having. Just constant clean and...

.. and what if the ink fails in a year or two? you will replace everything?

is the encoder strip clean all the way?

if I'm not mistaking, there was some tiny place at ink funnel, which is covered by ink when funnel is used. After wiping that the machine will think it's new. I have been drinking more than my share today, so don't blame me if i'm wrong :Big Laugh

I have 2 lan cards, other only for l265 only and other for net switch and internet

I have been thinking about buying IR heater, is there any cheap models? :)