• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

laminator

  1. Laminating Bubble Issue

    Hey, iam pretty New to Signmaking and iam biting my theeth out with laminating, i mostly Produce motocross Graphics. I have a certain Issue which i cant get along, even my fellow technician from the Company i have my machines from cant help me. I have the Problem that when i laminate certain...
  2. 5' 10' Flatbed Hot Laminator

    New Model Ancho máximo de laminado: 1300mm/ 51.22'' Longitud máxima de laminado: 2500mm/ 98.5'' Espesor máximo de laminado: 50mm/0.9'' Diámetro del rodillo: 130 mm Silicona (54kg) Temperatura máxima de laminación: 0-60°C/140°F 1.3*2.5m flatbed cold and hot factory laminator
  3. Kala Laminator Won't Feed

    I have a Mistral 1650, 55'' Laminator. When I try to run vinyl through the machine it won't feed the material. It pulls in the vinyl a little and then shoots it back out and does not move forward. It makes a large clacking sound when trying to feed.
  4. US Tech Laminator $999 Canadian / $750 US

    65" US Tech Cold Laminator for sale. Has a low spot at about the 37" mark. Arrived defective a few years back and they would not look after me in any way. Works great for up to 36" prints, or good for parts. Motors, foot swicth and everything else works like new. Located in Thunder Bay, Ontario
  5. Royal Sovereign Sigmont 65H heat assist laminator SoCal

    I have a like new Royal Sovereign Sigmont 65H Wide Format Roll Laminator with Heat Assist. I purchased this brand new from an authorized distributor to laminate vinyl stickers for a small start up. I used it very little and kept it covered when not in use. Essentially brand new. Please email...
  6. Need advice to buy a laminator.

    Hello! Im looking to buy a 60” laminator. I dont need heat. I want to know what you all would consider the best one I could buy as far as reliability and quality. And also what you all think about GFP laminators. Thank you for any help!
  7. Stuck on a setup step w/ brand new Gfp laminator

    Just assembled our new Gfp 350 TH. Super excited to start using it but currently stuck on a setup step. This could totally be a bonehead user error thing, many of these GFP components are new to me but I'm currently stumped. The groove doesn't line up with the opening of the cradle that the...
  8. Kala Arkane 1650 Laminator Replacement Part Needed

    Hi, Can someone please advise where I can find & buy a replacement part for the laminator (Kala Arkane 1650)? A plastic endcap on one side of the print guide (the metal piece) was broken that is used to keep the printed graphic flat during lamination. (See photos attached) Any information...
  9. ISSUE WITH ROYAL SOVEREIGN RSC-1401

    Hi there, I am relatively new to the signmaking world, and inherited a Royal Sovereign RSC-1401 laminator as part of our workflow. We use it most often for mounting vinyl to coroplast quickly, sometimes for lamination but usually not. The machine itself is 10+ years old. In the past weeks after...
  10. Looking to buy a laminator

    Hi I’m looking for some ideas on what laminator to purchase. I currently have a JCUV300-130 UV printer and I want to start doing more window graphics and wall graphics.
  11. Looking for laminator recommendation

    Our old laminator has been here longer than I have. It seems to have no brand or manual, and it's starting to fall apart. It's the only one I've ever used, so I don't even know if when it was new, it was a nice expensive one or totally cheapo.. There's no heating element or air compression. I'm...
  12. International Sign Association EXPO® 2022

    See you in Atlanta International Sign Association EXPO® 2022 CUTWORX USA USA Booth#4631 For a free Badge enter Promo Code: 10094 https://lnkd.in/efVP79z3 Be sure to check out the Never Stop Learning Contest in the Wrap Experience area of ISA 2022. The Wrap Experience™, powered by the...
  13. $18,500 - Afinia L801 Digital Label Printer & DLF-140S Finisher (Commercial Laminator/cut) - Located in Kansas

    We are the original owners. Purchased new in July 2021. MSRP of the machines was $23,845. Would like to sell combined but will entertain offers if you want just the printer or just the finisher. Lightly used. Printed approximately 125,000". Will likely need a new printhead on it, previous head...
  14. Wanted Looking for USED 60"^ Heat Assisted Laminator (seal, royal, GBC)

    Looking for a used 60" to 64" Laminator with heat assist to replace IMMEDIATELY. Brands preferred are Seal, Royal Sovereign and GBC. Need immediately! Located near Detroit, Michigan but will travel within a reasonable radius.
  15. Issues with laminator DRYTAC AFC

    Hello everyone! About month ago i bought used liqid laminator DRYTAC AFC. I have issue with that namely drying laminated prints(eco solvent). When I using a ceramic coil on the print i can see regular vartical strips in a whole material. Application roller is fine - clean and plain. Holes in...
  16. Laminator gone crazy need help

    Hy my Excelam Q 1200 laminator gone crazy tonight has kept working at high speed suddenly and now refuse to lower the speed. It as always worked well but now is set to high speed without any changes done with buttons. Can any one have had this issue or where should i look inside the machine to...
  17. GFP Laminators?

    Hello Signs101 - I'm looking for some feedback on GFP Laminators, how do they work, are they durable, do they track well, etc. We've had a Seal and a Drytac laminator, I was looking at a Flexa but it won't be available for several months and we need a laminator badly. We've also considered...
  18. Need Help Royal Sovereign - St. Louis area tech support needed

    I have a Royal Sovereign RSC-1650H that is in need of service. The roller when engaged down will not move forward, but when you raise it a tiny bit to take off the pressure, it will then go, but then there are bubbles on the print....so we have a problem. The emergency buttons are not engaged...
  19. CWT Galaxy Laminator and Applicator Table?

    Hello All - I'm in the market for a new laminator as well as an applicator table. I'm currently considering: 1) Seal 62 Pro D (already have one that is about 7 years old - runs well) 2) Kala Minstral 3) CWT Galaxy -- For Applicator Tables I'm considering: 1) CWT Evolution 2) Kala...
  20. Uneven laminating pressure RSL-2702

    Laminator: Royal Sovereign RSL-2702, about 3 years old Can anyone tell me why this is happening? I'm laminating cardstock pages of an emergency checklist binder with a kind of thick 5mil laminate. Normally I run everything fine at 248 degrees (F) and on speed 5. Well, none of the 40 or so...
Top