Search results

hello anyone have an old capping station need one plastic part that the cap sits on need 1 little bit with the guide pin mine have snapped off one side thanks

hello you need to go an join the mutoh groupo thing you download a program called value jet status monitor you will need your printer serial number I just done it

I fit a gold Teflon one from a stylus pro 7880 in a 1204 and it was good with no problemos

just bought a valuejet 628 were they released in 2014? it appears mine has the original carts in it from 2014 there is an error, when initialising going to measure the media, the head kind of jams. I have just taken the capping station from it and it appears on the near side the plastic pins...

what version of firmware lets me use a r2880 head I would prefer a Teflon/gold dx5 IF I use the 'latest' firmware for a cjv WILL a decoder card work?

comes with rasterlink 5 pro sg - does this run windows 10 IF the version comes with the printer, is the license mine - do I go online and update it - will I have the license - I cannot remove it from the old computer it was originally installed on. ---------------------------------- the printer...

hello do you still have the old head for sale? maybe I could fit that, I need to check I don't have other issues

FA06010 do you HAVE to use a FA head can I fit a 10 channel tfp head from a 4900/7900/11880 are the voltages set in the head for solvent rather than wate??? I have already fitted a 4900 head into a s30600 - -got head error, BUT still don't know if it was something else -thanks do you need a...

it wasn't in the printer list on install can I'imply'upgrade it to 7.3.2 for free have the cd and hasp

am getting error fatal head 1a39 or is it a duff head or duff ff's or both or main board time is first thing to check - service man mode and sensor check

message for mr bluespot is there supposed to be a clip that clips the 'off white' stiffening 'strips x2' to the carriage this don' t seem be in your pics, ad I'm missing this part also do you have a pic thanks pic 3 - ribbon to carriage

erm no, jig welded chassis, twin rail gantry non smelly solvent ink = WIN inspection hatch head swap = minutes pair cleaning etc etc pray tell, can I run s70600 gsx ink, in a s30600 gs2 machine or will ink 713100 200 300 400 cartrides read t6871 2 3 4 thanks

hello hello, I bought it used and dirt cheap = NO HEAD, warranty /\ didn't read this thread before throwing a USED 4900 HEAD (cheap) into the printer, just to see if it fired up IF I had I would have ok the lid off and cleaned out the track and fitted the new lines that came with it. I did...

aha I think I have bought one that's done the exact same thing

hello was this rectified after a capping station swap

so what you are saying is IF you don't oil the ribbon/ink tube rail, it may stick and might break flat cables, or worst still rip off the 90 degree ink line angle changer, and snap the plastic nipples from the connector, leaking ink everywhere, so then even after fitting a new head, angle...

http://www.aliexpress.com/item-img/10-pcs-Damper-DX6-DX7-Solvent-Resistant-For-Epson-Roland-Mutoh-Damper-CONNECTOR-3mm-x-2mm/32383678424.html?spm=2114.12010108.100005.10.a2LZDM if only I could 'just' buy them run 8 lines up from the carts straight to the dampers anyone know the bore of a mutoh...

helol somethink pumps from below, don't do what I did and leave the top lines off =idiot mess

how to how to omit the damper box top doofer and the 90 degree bit and not have a ink line joint above the flat cables alright, so you have to open two inkl ine channels that's cause the nips are so tight together o-ring and nut I...

also on a 30670 where is the main board where is the fuse p.s. the headboltare2 or 2.5 ??? th ar not th comon 3mm