Search results

On the CJ 500 you have 3 pinch rollers. The two rollers on the outsides are what gives the width of the material. Make sure you have the right side roller as far to the right as you can. Then the far left roller should be over the roller 3rd from the left. The middle pinch roller can go over...

I am about ready to install some eco sol inks into a cj500. I have seen some say the Eleven Ten are not that bad and some, like above, that say they are quite bad compared to Roland Eco Sol Max. I want to run this printer in a small room and it does have a window but in the winter it might not...

As far as I know each file once added must have the same settings IE:quality of print, diffusion, ICC profile etc. Size of image does not matter. I highlight the files I want nested (hold shift to add another and click on it) then in (file) nest the jobs. Most times it says there if files are...

I might be too late for your answer but I cut lexan with my router for my table hockey surfaces. I use a scrap of MDF or any scrap wood for the underside of the lexan and use an up spiral 1/4" bit. I cut mainly the 1/8" thickness and it cuts real nice. With the up cut spiral bit you will just...

If you have only done a couple med cleanings, try doing a few more. At times it has taken me several cleanings to get the head clear of whatever might have slipped in. What unit do you have?

You have the CMYK (just 4 colors) correct.. Make sure that versaworks is set up so that you have your ink set as such and not a CMYKLcLm or another ink set. I'm sure you would have it set right if other profiles have been working. I don't use vesaworks but just a thought. Also make sure...

It takes a bit more than just a cleaning to draw the ink back into the heads. Do as was just mentioned with a syringe and draw from the capping station so the ink is pulled into the heads. Find the tube that connects to the cap under the head with the problem. With a syringe you need that...

If what you have is just contamination, can you print the test print where you print a 1 inch or about that, strip of each color. On the Roland it's in the service manual. By doing this you will clear out whats in the print head and hopefully you would start seeing more LC. Next would be to...

Do you by any chance have AVG as your anti virus? For some reason with AVG you might get an error or a faulse virus reading. If you do use AVG you need to unistall it. Don't just try to exit the AVG as it still causes issues. Once all is loaded then re-install the AVG and it should not...

Not sure how many pinch rollers you have on that roll but you could try to remove that roll and set a thin strip (3" or so) of vinly under each roller and line them up evenly, then use the buttons to feed the media out and check if you can see if one roller is feeding out faster than the other...

Not sure if the Mutoh is anything like a Roland capping station but this happend to me. On the capping station when the heads are moved from the capping station the capps drop and slide to the left. As you reset the heads the station raises up and to the right and resets. Now on the front...

IF things are really clogged then you might want to get a refillable cartridge that you can put some cleaning fluid in. Then remove the line from the dampers and use a syringe to draw the cleaning solution into the line and let sit a bit then suck out the loosend crud. If you leave the dampers...

You might want to disconnect the line at the top of the dampers and do a manual flush with a syringe and a cleaning cartridge if you have. If you start drawing ink into the dampers and print heads right off the start you might get chunks of dried crud in both the dampers and print head which is...

As far as I know all the bulk refill carts are just gravity feed. There is an air hole in mine so they don't force the ink to the lines. The lines just draw the ink from the carts. The only issue might be is , do the refill carts need to be cleaned out once and a while or how long could you...

Yes the AVG does give a false virus and gives the 101 error message. You need to uninstall the AVG. It still won't work if you just exit out of the AVG or just try to turn it off. It must be uninstalled. I had the same issues on the colorchoice 4.5 rip when I tried to install it. Once you...

If you are doing that you might want to just use a syringe and attach it to the black line and draw enough to get the cleaning fluid to the end of the line in the dampers and then attach it back to the print head and do several regular cleanings to fill the print head. The powerful clean will...

I have had the odd time on a test print that there were a few lines spraying off a bit and a couple of cleanings would cure it. If you are still having issues after ( up to 10 cleanings ) then you might look at a new print head. It's hard to get things alligned when the heads are not working...

Great stuff Bo.

As far as customs goes they can code it so it's a duty free item even though they are made in Japan but sold in the States. You will have to pay the GST on the total purchace price in CND $$. If you can go get it you will save a pile in freight and crate charges. You might still need to get some...

Bump Anyone have older versions for sale that might work well?