Search results

Now I could be wrong, but my understanding that anything that runs TR2 inks (upgraded VG, VG2, VG3) has the service mode locked out. You can still perform basic maintenance tasks, but advanced procedures are locked out. I have a VG that runs firmware 3.10, but thus far have been avoiding upgrade...

The fact that the waste bottle got bigger doesn't provide a warm and fuzzy feeling...

The one that burns me is when it initiates a cleaning procedure at the end of short job, thereby blocking my ability to do a sheet cut for several minutes! There are some things on these machines that are not very well thought out in terms of execution for sure

Just curious, did you have the machine prior to TR2? I'm curious if you saw any sort of improvement. I'm assuming it's the white ink that's driving a lot my cleaning waste...

That's disappointing. Seems like a similar amount to what my VG-640 goes through in a week with aftermarket TR ink. I was hoping upgrading to TR2 would improve that.

Sorry for the delay, got caught up in a landscaping project! Since going with the Roland dampers, I haven't had any issues (which has been about a year now). It seems to take just the smallest of air leaks in the ink path to cause problems. One of the things I've found helpful is to pull the...

I had very similar looking test prints on my VG-640 awhile back, turns out it was junk dampers. Check out this thread, maybe it helps you... https://www.signs101.com/threads/vg-640-strange-test-print-any-ideas.169282/

I've had similar looking test prints on my VG at times when it sits for awhile. As long as the cap tops are in good shape (as Zoogee says), it comes back with some combination of cleaning, manual cleaning, or doing a test print with large areas of C, M, Y, K. I can't speak to any newer...

I can attest to staying away from captops and dampers on Digiprint; my issues went away after replacing with Roland parts. In general, I use the rule that aftermarket parts are probably OK as long as they're not electrical, electronic, require a precision fit/function, or are a structural...

I've had a chance to dive deeper into the malfunctioning pump and thought I'd share with the group. After fully cracking open the pump, I discovered what I missed in my quick initial peek. There are 2 plastic tabs that are used to control the position of the rollers. It seems one was...

Alright! So nearly exactly a month later (due to waiting for parts)...it appears the issue was the pump. He's how I got there: After observing the system a bit more, I noticed that by gently placing a finger on top of the filter (Roland seems to refer to this as a valve-assy, but sure seems to...

Hi everyone, I'm looking for some advice. My VG-640 has been working well for the past several months and just this week started throwing a 0380 [0040] code. Initially a couple of power cycles would get it to come back, but that stopped working. I popped the head cover off and sure enough the...

Sorry, guess maybe I should've specified that it's the front half of the wheel well to be more clear. A picture is worth 1000 words. Here's what they typically look like when open - as a reference for others.

While I'm not familiar with this particular generation of Peterbilt, on trucks they typically design it so that about 1/2 of the wheel well goes up with the hood for easy service. To check the oil, you typically stand between the engine and front wheel. I'm actually curious about answers to...

Unfortunately, I can't help you on the ink tube adjustment; I converted my VG-640 from 7 to 8 color, but apparently that doesn't require any adjustment to be done. I suspect this is documented only in a full Roland Service manual. I will give you fair warning, however, that the conversion...

I think you may have just saved the resale value of a bunch of VG and VG2 machines. Thanks so much for sharing with us!!

These are the results of a bunch of people getting together in a room and discussing ways they can make more money this year. It's an inevitable conclusion if you feel your customers are as captive as fish in a barrel. I don't have a lot of hope it's going to get better. Many people don't seem...

Please tell us more. I'm curious about this as well. I can't even get the local dealer to return my calls (when I want to give them money!), so curious how you got Roland to respond...

I lied. I actually use aftermarket inks for the 7 colors. White is only available in TR, and I have to scour the open market for it. Fortunately, it's not a color I use a ton of. Ultimately, it is what will lead me to doing the TR2 upgrade - I'm hoping to get at least 6 months of problem-free...

Are you looking to buy it? Or asking for a friend? ;-) I recently picked up a VG-640 after searching the past couple years for used machines. The VG series seems to be a bit rare on the used market compared to other Roland models, so it's hard to gauge the dollar value. There is a lot of bad...