flexi

Is someone available to teach me print and cut online through Zoom ? I have a Mutoh printer and recently got a Graphtec cutter. I need someone to teach me how to use Registration marks and just the basics on Flexi. My email address is hooshmand.f66@gmail

We have been having massive issues with cut size inaccuracies on a brand new summa s2 160 T cutter, hp latex 560, and sai flexi. We tested the same jobs through winplot and got perfect results. However, when doing it with flexi the cut sizes range from 2mm too big to 1mm too small on small cuts...

I have a template from SRGFX that I already have my design completed with. How do I go about just being able to print and cut what design I have showing within the clipping mask without having to print the entire design and then having a bunch of scraps? I can only seem to add a contour cut to...

Hey everyone, I am looking for suggestions on a sturdy roll media that I can use my HP Latex 64 Cutter to make templates. We are currently using a Sihl paper, but it is too lightweight and when I try to plot out a template, it either is too much pressure or not enough. What does everyone use...

We are using latex 335 HP printer almost about 8 months. This printer comes with Flexi12 RIP included. Usually we print a big nested jobs at once and only from tiff files. First bad experience we had was after couple of days of usage. We had a buggy output of some files (attachment). Of course...

Hi all, I'm wondering if it's possible to lay one summa barcode next to each other (side by side). I'm trying to improve the accuracy over very small stickers. Instead of copying them individually to hundreds (not accurate over certain length). I prefer to make them as a set then copy the set...

Curious if anyone has seen this sort of "ghosting" in a RIP before? These are very small shapes, and I did play with levels a hair to get the ghosting to show up a little better (probably not visible on all monitors, before you call me nuts). There are arrows that show where the "ghosting"...

I have a Boss Laser and I want to add it as a (printer/cutter/engraver) to Flexi. Has anyone had any success? What profile in Flexi? I know I can go from Corel to it so there must be a way.

anyone fogured our how to reliably do this? I mean Hp has through their app but wondered how to do it directly from my phone. Not so much like sending new jobs but if I were somewhere and wanted to send a job I have already printed through production manager. On the other hand what if I wanted...

Hello, I'd like to kindly request some assistance from my fellow sign people: I need to convert the "Flex Cut" settings in my Flexi over to my Onyx Thrive (Summa's term for "Through Cut") May you please take a look below at the image denoting the settings in each and assisting me with the...

https://www.thinksai.com/flexi19 Flexi 12 to Flexi 19...

To start I apologize if I'm in the wrong section. I've had a Vj1204 for quite some time now, I still use Flexi 10 and am using pre-made profiles. My most recent job has a ton of gradients from black to white. Obviously black to white gradients use all levels of grey. in the darker section of...

Not sure what I hit but half my fonts in flexi 8.1 are now fuzzy on edge almost like hair ...please help

Looking for suggestions on software for shop drawings. We currently use Illustrator almost exclusively, but this is not very practical as most of our designers' time is getting tied up in spec'ing details (sizing/finishes/ect) or laying out the actual pages, rather than designing signs. We are a...

Looking to create a fade with dots instead of the gradient. Pictures attached/ need 36" wide x 3.5" on starts full black to smaller dots to make it look white. Any help appreciated. Working in Flexi

I do kart graphics, but wondering how the prism vinyl is added to the designs. Is it cut out and layed ontop of the printer vinyl or is the design printed on the prism vinyl? The prism vinyl would primarily be used to outline numbers and maybe a couple accent designs. Also for flourescent in...

Hello guys, I suppose this isn't really a big deal, but has anybody found if there's a way for the measurement tool within Flexi (I'm using Flexi 12) to display its results in fraction form instead of decimal? I can't think of any reason why it would be deemed relevant to show something as...

Hello, I Have a Gerber Edge LE, and i am using flexi (cloud) and have been for 2 years and using it for single basic colors of cmyk seems to be doing OK but when i try to print full color images with it i seem to be having a lot of issues, i have quite a few different color foils mostly all...

Hi. We upgraded our Flexi software last year from 10.X to 12.X, since the endex of upgrading from Flexi 10.X was announced. There was not much new features in the program, and all seamed very similar to the earlier version. However, there are some small things that puts some pebbles in the...

Hi all, Got questions regarding flexi flex cut and summa. Been using the contour cut for a while but never really used the flexcut. So this is my first try. Setup the file in illustrator, created 2 spot colours, named CutContour and PerfCutContour. Also separate the curves into 2 layers. Flexi...