Search results

It's a cost of doing business that is reflected in our prices already. If you want to pay for a $30k printer with a card though, we have to charge a fee if we don't want to lose our hat.

I agree with Jim. It looks like an electrical issue. I would make sure the encoder is clean as well as sometimes it can look like an electrical issue when it's just a dirty encoder. If it's clean and still looks like that, you could have a bad cables or board somewhere in the machine.

Although it doesn't look like typical drop out, I would start with changing out the dampers especially if they haven't been changed out in the last 12 to 24 months. The nozzle check looks fine other than a few deflecting nozzles in the black but that shouldn't affect the print too much. Also...

I agree! Anytime someone is selling something for less than half of what everyone else is selling it, it's either stolen or a scam. And believe me, scammers are always trying to steal print heads from us to, I can only assume, resell at a much lower price.

It's not going to support Intel processors before 8th gen. All you guys running old XP and Windows 7 computers are out of luck! Not that you're the type to upgrade anyway :D

Go to Mimaki's website and download the latest USB driver. They tend to update the driver and it conflicts with certain versions of FineCut until you update it.

Check us out for the most common parts. A lot of the common parts for the SP300 are use din other machines so they are easier to find. For anything else we don't have or you can't find, try Ordway Sign Supplies in the southern cali. As for the original post, that test print looks like there...

Tell him to go to a window tinting place and they'll throw some clear bra on the areas that are most susceptible to getting chipped.

Am I reading the picture correctly and the cut is about 1.5" too far up? If that's the case, are you printing and cutting immediately after or are you laminating or something like that in between?

Error 07 is a head heat error which means the head circuit is shorting out. Check your head cables for damage or ink splatter on the silver leads and replace if needed. Other than that, basically anything that would short out the circuit is causing the issue like another bad cable deeper in the...

I'll let you in on a little trick of the trade. Install the old malfunctioning head back into the machine with the head memory board plugged in. Then boot the machine in service mode (power on while holding function and remote). Then go into the menu and scroll down the the #adjust menu. In that...

Make sure the encoder is still in between the encoder sensor all the way across the machine. If the sensor is not straddling the encoder, it can't read it. If that looks good, I would start by changing the sensor out. This error specifically means that the main board didn't receive a value from...

You can access the log files via a computer and the proper Mimaki software. Mimaki just doesn't give it to end users.

I'm not having a glass of wine, I'm having 6. It's called a tasting and it's classy.

It looks like the cyan is probably having ink flow issues. I would disconnect the cap top from the pump and try to pull ink through with a syringe while the heads are capped. If you pull air and the syringe doesn't pull back on you, you need a new cap top. If you pull and get suction but no ink...

Normally when one channel drops like that it's going to be an ink flow issues such as a bad damper, broken manifold, or air getting in the system through a leak. The fact that there are two full channels missing tells me this is electronic though. My best guess is a damaged head board. Most...

Which is well worth it if something goes wrong.

I have a no tolerance policy for abusive customers. Upset about a mistake we made? I'll do everything I need to make it right. But the second it becomes abusive, you're done. At 50% you're sort of hamstrung though. I'd raise your prices on him and start seeking as many new customers a possible...

I just responded to your request on our site but figured I'd followup here. Mutoh only sells through dealers like us. They don't recommend end users replace boards but I've helped many people do so over email. The only issue is when you do it yourself, even with my help, there is no warranty...

It's sort of like the UPS/FedEx debate. Whoever wronged you last is the worst supplier. For every brand, I could find someone who thinks they're junk and someone who thinks they are the best. Your better bet would be to research the technologies and see which one works best for you. All of the...